LTC3731HG Linear Technology, LTC3731HG Datasheet - Page 19

• Manufacturer Part Number: LTC3731HG
• Description: IC REG SW SYNC 3PH STPDWN 36SSOP
• Manufacturer: Linear Technology
• Series: PolyPhase®r
• Type: Step-Down (Buck)r

Specifications of LTC3731HG

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.6 ~ 6 V
• Frequency - Switching: 225kHz ~ 680kHz
• Voltage - Input: 4 ~ 36 V
• Operating Temperature: -40°C ~ 140°C
• Mounting Type: Surface Mount
• Package / Case: 36-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Output: -
• Power - Output: -
• Lead Free Status / Rohs Status: Not Compliant

applicaTions inForMaTion
Current Foldback
In certain applications, it may be desirable to defeat the
internal current foldback function. A negative impedance
is experienced when powering a switching regulator. That
is, the input current is higher at a lower V
as V
commodate a normal, resistive load having increasing
current draw with increasing voltage. The EAIN pin should
be artificially held 70% above its nominal operating level
of 0.6V, or 0.42V in order to prevent the IC from “folding
back” the peak current level. A suggested circuit is shown
in Figure 8.
The emitter of Q1 will hold up the EAIN pin to a voltage in
the absence of V
circuitry from reducing the peak output current. Remov-
ing the function in this manner eliminates the external
MOSFET’s protective feature under short-circuit conditions.
This technique will also prevent the short-circuit latchoff
function from turning off the part during a short-circuit
event and the peak output current will only be limited to
N • 75mV/R
Undervoltage Reset
In the event that the input power source to the IC (V
drops below 4V, the RUN/SS capacitor will be discharged
to ground. When V
will be allowed to recharge and initiate another soft-start
turn-on attempt. This may be useful in applications that
switch between two supplies that are not diode connected,
IN
is increased. Current foldback is designed to ac-
SENSE
OUT
.
CC
that will prevent the internal sensing
rises above 4V, the RUN/SS capacitor
IN
CALCULATE FOR
0.42V TO 0.55V
Figure 8. Foldback Current Elimination
and decreases
V
CC
CC
)
Q1
but note that this cannot make up for the resultant inter-
ruption of the regulated output.
Phase-Locked Loop and Frequency Synchronization
The IC has a phase-locked loop comprised of an internal
voltage controlled oscillator and phase detector. This allows
the top MOSFET of output stage 1’s turn-on to be locked
to the rising edge of an external source. The frequency
range of the voltage controlled oscillator is ±50% around
the center frequency f
pin of 1.2V corresponds to a frequency of approximately
400kHz. The nominal operating frequency range of the IC
is 225kHz to 680kHz.
The phase detector used is an edge sensitive digital type
that provides zero degrees phase shift between the external
and internal oscillators. This type of phase detector will
not lock the internal oscillator to harmonics of the input
frequency. The PLL hold-in range, ∆f
capture range, ∆f
The output of the phase detector is a complementary pair
of current sources charging or discharging the external
filter components on the PLLFLTR pin. A simplified block
diagram is shown in Figure 9.
If the external frequency (f
cillator frequency, f
pulling up the PLLFLTR pin. When the external frequency is
less than f
∆f
V
EAIN
CC
H
LTC3731H
= ∆f
OSC
C
3731H F08
= ±0.5 f
, current is sunk continuously, pulling down
C
:
OSC
O
O
. A voltage applied to the PLLFLTR
, current is sourced continuously,
PLLIN
) is greater than the os-
LTC3731H
H
, is equal to the

3731Hfb