LT1977EFE#PBF Linear Technology, LT1977EFE#PBF Datasheet - Page 8

• Manufacturer Part Number: LT1977EFE#PBF
• Description: IC REG SW 1.5A HV STP DN 16TSSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LT1977EFE#PBF

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 1.2 ~ 54 V
• Current - Output: 1.5A
• Frequency - Switching: 500kHz
• Voltage - Input: 3.3 ~ 60 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP Exposed Pad, 16-eTSSOP, 16-HTSSOP
• Primary Input Voltage: 60V
• No. Of Outputs: 1
• Output Voltage: 54V
• Output Current: 3.5A
• No. Of Pins: 16
• Operating Temperature Range: -40°C To +125°C
• Msl: MSL 1 - Unlimited
• Rohs Compliant: Yes
• Dc To Dc Converter Type: Step Down
• Pin Count: 16
• Input Voltage: 60V
• Switching Freq: 575KHz
• Package Type: TSSOP EP
• Output Type: Adjustable
• Switching Regulator: Yes
• Mounting: Surface Mount
• Input Voltage (min): 2.4V
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Compliant

LT1977
BLOCK DIAGRA
The LT1977 is a constant frequency, current mode buck
converter. This means that there is an internal clock and two
feedback loops that control the duty cycle of the power
switch. In addition to the normal error amplifier, there is a
current sense amplifier that monitors switch current on a
cycle-by-cycle basis. A switch cycle starts with an oscilla-
tor pulse which sets the RS latch to turn the switch on. When
switch current reaches a level set by the current compara-
tor the latch is reset and the switch turns off. Output volt-
age control is obtained by using the output of the error
amplifier to set the switch current trip point. This technique
means that the error amplifier commands current to be
8
10
14
15
12
11
13
4
9
7
V
BIAS
SYNC
SHDN
C
FB
V
PGFB
C
IN
SS
C
T
1.25V
1.12V
1.3V
+
–
COMP
SHDN
W
UNDERVOLTAGE
–
+
+
–
INTERNAL REF
ERROR
SOFT-START
COMP
SHUTDOWN
AMP
FOLDBACK
LOCKOUT
THERMAL
PG
DETECT
2.4V
Figure 1. LT1977 Block Diagram
BURST MODE
OSCILLATOR
ANTISLOPE
DETECT
1.2V C
500kHz
CLAMP
CLAMP
SLOPE
COMP
COMP
V
C
T
delivered to the output rather than voltage. A voltage fed
system will have low phase shift up to the resonant fre-
quency of the inductor and output capacitor, then an abrupt
180° shift will occur. The current fed system will have 90°
phase shift at a much lower frequency, but will not have the
additional 90° shift until well beyond the LC resonant fre-
quency. This makes it much easier to frequency compen-
sate the feedback loop and also gives much quicker tran-
sient response.
Most of the circuitry of the LT1977 operates from an
internal 2.4V bias line. The bias regulator normally draws
Σ
CURRENT
COMP
R
S
SWITCH
+
–
LATCH
Q
CIRCUITRY
DRIVER
BOOST
PGND
GND
SW
PG
1977 BD
1977fa
16
17
6
2
8