MAX8620YETD+T Maxim Integrated Products, MAX8620YETD+T Datasheet
MAX8620YETD+T
Specifications of MAX8620YETD+T
Related parts for MAX8620YETD+T
MAX8620YETD+T Summary of contents
Page 1
... MSM is a trademark of QUALCOMM, Inc. XScale is a trademark of Intel Corp. ARM is a trademark of ARM Limited. OMAP is a trademark of Texas Instruments, Inc. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. in Portable Equipment ♦ ...
Page 2
Microprocessors or DSPs in Portable Equipment ABSOLUTE MAXIMUM RATINGS IN1, IN2, PWR_ON, RESET, EN2, SEL1, SEL2, HF_PWR, FB GND ..................................-0.3V to +6.0V OUT1, OUT2 to GND .................................-0. Current ......................................................................1.5A Continuous Power Dissipation (T ...
Page 3
Microprocessors or DSPs ELECTRICAL CHARACTERISTICS (continued +3.7V 10µF, C IN1 IN2 IN BP (Note 1) PARAMETER SYMBOL OUT1, OUT2 Power-Supply Rejection Ratio Output Noise Voltage STEP-DOWN CONVERTER (OUT3) Output Voltage Range V ...
Page 4
Microprocessors or DSPs in Portable Equipment ( 3.7V, PWR_ON = IN1 2.2µH (LQH31CN2R2M53), C IN1 IN2 150kΩ 75kΩ), C = 10µ 0.01µ +25°C, unless ...
Page 5
Microprocessors or DSPs ( 3.7V, PWR_ON = IN1 2.2µH (LQH31CN2R2M53), C IN1 IN2 150kΩ 75kΩ), C = 10µ 0.01µ +25°C, unless otherwise noted.) A ...
Page 6
Microprocessors or DSPs in Portable Equipment ( 3.7V, PWR_ON = IN1 2.2µH (LQH31CN2R2M53), C IN1 IN2 150kΩ 75kΩ), C = 10µ 0.01µ +25°C, unless ...
Page 7
Microprocessors or DSPs PIN NAME LDO Output-Voltage Select Input 1. SEL1 and SEL2 set the OUT1 and OUT2 voltages to one of nine 1 SEL1 combinations (Table 1). LDO Output-Voltage Select Input 2. SEL1 and SEL2 set the ...
Page 8
Microprocessors or DSPs in Portable Equipment Detailed Description The MAX8620Y µPMIC is designed to power low-core- voltage microprocessors or DSPs in portable devices. The µPMIC contains a fixed-frequency, high-efficiency step-down converter; two low-dropout regulators (LDOs); a 30ms (min) ...
Page 9
Microprocessors or DSPs Voltage-Positioning Load Regulation As seen in Figure 2, the MAX8620Y uses a unique step- down converter feedback network. By taking feedback from the LX node through R1, the usual phase lag due to the output ...
Page 10
Microprocessors or DSPs in Portable Equipment IN1 MAX8620Y PWR_ON ON/OFF HF_PWR LOGIC EN2 LDO THERMAL SENSOR BP GND Figure 3. Linear-Regulator Functional Diagram LDO Output-Voltage Selection (SEL1, SEL2) As shown in Table 1, the LDO output voltages, OUT1 ...
Page 11
Microprocessors or DSPs Table 2. MAX8620Y Power Modes PWR_ON HF_PWR rising edge at HF_PWR initiates a 1.31s one-shot timer. The status of HF_PWR shown in Table 2 indicates whether the one-shot period ...
Page 12
Microprocessors or DSPs in Portable Equipment Reset Output ( RESET ) RESET is an open-drain, active-low output that indi- cates the status of OUT1. RESET is typically pulled up through a 100kΩ resistor to the system logic voltage. ...
Page 13
Microprocessors or DSPs If a long-key press is preferred, see must remain high until a microprocessor asserts a logic- high signal when using this circuit system includes multiple power-on sources, use a diode OR configura- tion, ...
Page 14
Microprocessors or DSPs in Portable Equipment Table 3. Suggested Inductors MANUFACTURER SERIES LB2012 LB2016 LB2518 Taiyo Yuden LBC2518 CB2012 CB2016 CB2518 LQH32C_53 Murata LQM43FN D310F TOKO D312C Sumida CDRH2D11 14 ______________________________________________________________________________________ INDUCTANCE ESR CURRENT RATING (µH) (Ω) 1.0 ...
Page 15
Microprocessors or DSPs Capacitor Selection Step-Down Converter Output Capacitor The output capacitor required to keep the OUT3 output voltage ripple small and to ensure regulation loop stability. C must have low impedance at the OUT3 ...
Page 16
Microprocessors or DSPs in Portable Equipment Connect GND to the ground plane. The external feed- back network should be very close to the FB pin, within 0.2in (5mm). Keep noisy traces, such as the LX node, as short ...
Page 17
Microprocessors or DSPs (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) D PIN 1 INDEX AREA -DRAWING NOT TO SCALE- ______________________________________________________________________________________ in Portable ...
Page 18
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products ...