BTS650P Infineon Technologies, BTS650P Datasheet - Page 5

• Manufacturer Part Number: BTS650P
• Description: SWITCH HI-SIDE CURRNT TO-220AB/7
• Manufacturer: Infineon Technologies
• Series: PROFET®r
• Type: High Sider

Specifications of BTS650P

• Input Type: Non-Inverting
• Number Of Outputs: 1
• On-state Resistance: 4.4 mOhm
• Current - Output / Channel: 70A
• Current - Peak Output: 130A
• Voltage - Supply: 5 V ~ 34 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Through Hole
• Package / Case: TO-220-7 (Bent Leads)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: BTS650PIN; SP000011287

Parameter and Conditions
at T
Protection Functions
Short circuit current limit
Short circuit shutdown delay after input current
positive slope, V
min. value valid only if input "off-signal" time exceeds 30 s
Output clamp
(inductive load switch off)
see diagram Ind. and overvolt. output clamp page 8
Output clamp (inductive load switch off)
Short circuit shutdown detection voltage
Thermal overload trip temperature
Thermal hysteresis
Reverse Battery
Reverse battery voltage
On-state resistance
Integrated resistor in V
16
17
18
Infineon Technologies AG
V
I
) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
) This output clamp can be "switched off" by using an additional diode at the IS-Pin (see page 8). If the diode
) The reverse load current through the intrinsic drain-source diode has to be limited by the connected load (as
V
at V
(pin 4 to pins 1,2,6,7)
L
bb
= 40 mA
ON
j
data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not
designed for continuous repetitive operation.
is used, V
it is done with all polarity symmetric loads). Note that under off-conditions (I
is not activated. This results in raised power dissipation due to the higher voltage drop across the intrinsic
drain-source diode. The temperature protection is not active during reverse current operation! Increasing
reverse battery voltage capability is simply possible as described on page 9.
= -40 ... +150 °C, V
= -12V, V
= 12 V, time until shutdown max. 350 s
OUT
= V
OUT
bb
IN
17
- V
= 0, I
is clamped to V
)
ON
ON(CL)
> V
bb
L
(Pins 1 ,2 ,6 ,7 to pin 4)
= - 20 A, R
= 12 V unless otherwise specified
ON(SC)
bb
16
(e.g. over voltage)
)
18
(Tab to pins 1, 2, 6, 7)
line
)
bb
- V
IS
ON(CL)
= 1 k
at inductive load switch off.
T
c
I
T
T
L
T
j
=+150°C:
T
c
= 40 mA:
Page 5
= 150 °C:
c
j
=-40°C:
= 25 °C:
=25°C:
I
I
I
t
-V
V
V
T
-V
R
R
Symbol
L(SC)
L(SC)
L(SC)
d(SC)
jt
T
ON(CL)
ON(SC)
ON(rev)
bb
OUT(CL)
bb
jt
IN
150
min
Data Sheet BTS650P
--
--
65
80
14
39
= I
--
--
--
--
--
IS
= 0) the power transistor
Values
16.5
110
130
115
120
5.4
8.9
typ
42
10
--
--
--
6
2003-Oct-01
180
12.3
max
350
--
--
7.0
20
47
16
--
--
--
--
Unit
m
°C
A
V
V
V
K
V
s