ATA6829-T3QY 71 Atmel, ATA6829-T3QY 71 Datasheet - Page 5

• Manufacturer Part Number: ATA6829-T3QY 71
• Description: IC DRIVER TRPL HALFBRIDGE 16PSOP
• Manufacturer: Atmel
• Type: High Side/Low Side Driverr

Specifications of ATA6829-T3QY 71

• Input Type: Serial
• Number Of Outputs: 6
• On-state Resistance: 1.1 Ohm
• Current - Peak Output: 2A
• Voltage - Supply: 5.6 V ~ 40 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: 16-PSOP
• Product: Half-Bridge Drivers
• Rise Time: 100 ns
• Fall Time: 100 ns
• Supply Voltage (max): 40 V
• Supply Current: 350 uA
• Maximum Operating Temperature: + 150 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 55 C
• Number Of Drivers: 3
• Output Current: - 10 A to + 10 A
• Output Voltage: 40 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output / Channel: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

After power-on reset, the input register has the following status:
The following patterns are used to enable internal test modes of the IC. It is not recommended to use these patterns during
normal operation.
4531G–BCD–07/09
Bit 15
Bit 15
SI
H
H
H
H
Bit 14
Bit 14
OCS
H
H
H
H
(OCS)
Bit 13
Bit 13
OLD
H
H
H
H
Bit 12
Bit 12
PH3
H
Table 3-2.
L
L
L
Bit
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
Bit 11
Bit 11
PL3
H
L
L
L
Output (Status)
Bit 10
Status HS1
Status HS2
Status HS3
Status LS1
Status LS2
Status LS3
Bit 10
Output Data Protocol
PH2
Register
H
L
L
L
n. u.
n. u.
n. u.
n. u.
n. u.
n. u.
OVL
PSF
INH
TP
Bit 9
Bit 9
PL2
H
L
L
L
Bit 8
Function
Temperature prewarning: high = warning
Normal operation: high = output is on, low = output is off
Open-load detection: high = open load, low = no open load
(correct load condition is detected if the corresponding output is switched
off); not affected by SRR
Normal operation: high = output is on, low = output is off
Open-load detection: high = open load, low = no open load
(correct load condition is detected if the corresponding output is switched
off); not affected by SRR
Description see LS1
Description see HS1
Description see LS1
Description see HS1
Not used
Not used
Not used
Not used
Not used
Not used
Over-load detected: set high, when at least one output is switched off by
a short-circuit condition or an overtemperature event. Bits 1 to 6 can be
used to detect the affected switch.
(open-load detection bit OLD = high)
Inhibit: this bit is controlled by software (bit SI in input register)
High = standby, low = normal operation
Power-supply fail: undervoltage at pin VS detected
Bit 8
PH1
H
L
L
L
Bit 7
Bit 7
PL1
H
L
L
L
(HS3)
Bit 6
Bit 6
HS3
L
L
L
L
(LS3)
Bit 5
Bit 5
LS3
L
L
L
L
(HS2)
Bit 4
Bit 4
HS2
L
L
L
L
(LS2)
Bit 3
Bit 3
LS2
L
L
L
L
(HS1)
Bit 2
Bit 2
HS1
L
L
L
L
ATA6829
(LS1)
Bit 1
Bit 1
LS1
L
L
L
L
(SRR)
Bit 0
Bit 0
SRR
L
L
L
L
5