VND600SP STMicroelectronics, VND600SP Datasheet - Page 17

• Manufacturer Part Number: VND600SP
• Description: IC DRIVER DUAL 36V 25A PWRSO-10
• Manufacturer: STMicroelectronics
• Type: High Sider

Specifications of VND600SP

• Input Type: Non-Inverting
• Number Of Outputs: 2
• On-state Resistance: 30 mOhm
• Current - Peak Output: 40A
• Voltage - Supply: 5.5 V ~ 36 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: PowerSO-10 Exposed Bottom Pad
• Switch Type: High Side
• Power Switch Family: VND600SP
• Power Switch On Resistance: 30mOhm
• Output Current: 25A
• Mounting: Surface Mount
• Supply Current: 6mA
• Package Type: PowerSO
• Operating Temperature (min): -40C
• Operating Temperature (max): 150C
• Operating Temperature Classification: Automotive
• Pin Count: 12
• Power Dissipation: 96.1W
• Load Current Rating: 25 A
• Relay Type: Solid State
• Termination Style: Solder Leads
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Output / Channel: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 497-2711-5

VND600SP
3.1.2
3.2
3.3
Please note that, if the microprocessor ground is not shared by the device ground, then the
R
values. This shift will vary depending on how many devices are ON in the case of several
high-side drivers sharing the same R
If the calculated power dissipation requires the use of a large resistor, or several devices
have to share the same resistor, then ST suggests using solution 2 below.
Solution 2: a diode (D
A resistor (R
an inductive load. This small signal diode can be safely shared amongst several different
HSD. Also in this case, the presence of the ground network will produce a shift (j600mV) in
the input threshold and the status output values if the microprocessor ground is not common
with the device ground. This shift will not vary if more than one HSD shares the same
diode/resistor network. Series resistor in INPUT and STATUS lines are also required to
prevent that, during battery voltage transient, the current exceeds the Absolute Maximum
Rating. Safest configuration for unused INPUT and STATUS pin is to leave them
unconnected.
Load dump protection
D
V
line that are greater than those shown in the ISO T/R 7637/1 table.
MCU I/O protection
If a ground protection network is used and negative transients are present on the V
the control pins will be pulled negative. ST suggests to insert a resistor (R
prevent the µC I/O pins from latching up.
The value of these resistors is a compromise between the leakage current of µC and the
current required by the HSD I/Os (Input levels compatibility) with the latch-up limit of µC
I/Os:
Example
For the following conditions:
Recommended values are:
CC
GND
ld
is necessary (voltage transient suppressor) if the load dump peak voltage exceeds the
maximum DC rating. The same applies if the device is subject to transients on the V
- V
V
I
V
5k
R
latchup
will produce a shift (I
OH C
CCpeak
prot
CCpeak
R
= 10k
prot
GND
= - 100V
4.5V
20mA
/ I
latchup
65k .
= 1k ) should be inserted in parallel to D
R
prot
S(on)max
GND
(V
OH C
) in the ground line
* R
GND
- V
GND
IH
.
) in the input thresholds and the status output
- V
GND
) / I
IHmax
GND
if the device will be driving
Application information
prot
) in line to
CC
line,
17/26
CC