L6566A STMicroelectronics, L6566A Datasheet - Page 28

• Manufacturer Part Number: L6566A
• Description: IC CTRLR OVP UVLO 16SOIC
• Manufacturer: STMicroelectronics

Specifications of L6566A

• Output Isolation: Isolated
• Frequency Range: 93 ~ 107kHz
• Voltage - Input: 8 ~ 23 V
• Power (watts): 750mW
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Output Current: 800 mA
• Output Power: 750 mW
• Input Voltage: 8 V to 23 V
• Operating Temperature Range: - 40 C to + 150 C
• Mounting Style: SMD/SMT
• Duty Cycle (max): 75 %
• Universal Input Mains Range: 90÷264Vac - Frequency 45 ÷ 65 Hz
• Output Voltage: 19 V@4 A continuous operation
• Mains Harmonics: Acc. to EN61000-3-2 Class-D
• St-by Mains Consumption: Less than 0.25 W @265Vac
• Overall Efficiency: Better than 86%
• Emi: According to EN55022-Class-B
• Safety: According to EN60950
• Low Profile Design: 25 mm maximum height
• Pcb Single Layer: single side, 70 μm, CEM-1, 78x174 mm, Mixed PTH/SMT
• For Use With: 497-8834 - BOARD DEMO FOR L6563/LL6566A497-6452 - BOARD EVAL FOR L6566B497-6451 - BOARD EVAL FOR L6566B497-6450 - BOARD EVAL FOR L6566B497-6449 - BOARD EVAL FOR L6566A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Application information
Note:
28/51
Figure 16. Typical power capability change vs input voltage in QR flyback
It acts on the overcurrent setpoint V
Vin (output of the PFC pre-regulator) sensed through a dedicated pin (15, VFF): the higher
the input voltage, the lower the setpoint. This is illustrated in the diagram on the left-hand
side of
and V
regulation):
Equation 5
If the voltage on the pin exceeds 3 V switching ceases but the soft-start capacitor is not
discharged. The schematic in
in the control loop.
With a proper selection of the external divider R1-R2, i.e. of the ratio k = R2 / (R1+R2), it is
possible to achieve the optimum compensation described by the lower curve in the diagram
of
The optimum value of k, k
voltage range, is the one that provides equal power capability at the extremes of the range.
The exact calculation is complex, and non-idealities shift the real-world optimum value from
the theoretical one. It is therefore more practical to provide a first cut value, simple to be
calculated, and then to fine tune experimentally.
Assuming that the system operates exactly at the boundary between DCM and CCM, and
neglecting propagation delays, the following expression for k
Equation 6
Figure 16
csx
Figure 17 on page 29
(with the error amplifier saturated high in the attempt of keeping output voltage
.
converters
2.5
1.5
0.5
2
1
k
1
opt
opt
=
, which minimizes the power capability variation over the input
: it shows the relationship between the voltage on the pin VFF
Figure 17 on page 29
3
⋅
1.5
V
V
csx
in
csx
min
=
, so that it is a function of the converter’s input voltage
⋅
1
V
2
−
in
max
V
VFF
3
V
+
inmin
V
2.5
(
in
=
V
V
compensated
system optimally
R
in
system not
compensated
1
min
−
shows also how the function is included
k
3
+
Vin
V
3
in
max
opt
)
can be found:
⋅
3.5
V
R
k = k
k = 0
k
opt
4
L6566A