ICE3BR0665JF Infineon Technologies, ICE3BR0665JF Datasheet - Page 16

• Manufacturer Part Number: ICE3BR0665JF
• Description: IC OFFLINE CTLR SMPS OTP TO220-6
• Manufacturer: Infineon Technologies
• Series: CoolSET®F3Rr
• Type: Off Line Switcherr

Specifications of ICE3BR0665JF

• Output Isolation: Isolated
• Frequency Range: 58 ~ 75kHz
• Voltage - Input: 10.5 ~ 27 V
• Voltage - Output: 650V
• Power (watts): 42W
• Operating Temperature: -25°C ~ 130°C
• Package / Case: TO-220-6 Formed Leads
• Output Voltage: 650 V
• Input / Supply Voltage (max): 27 V
• Input / Supply Voltage (min): - 0.3 V
• Duty Cycle (max): 75 %
• Switching Frequency: 67 KHz
• Operating Temperature Range: - 25 C to + 130 C
• Mounting Style: Through Hole
• Maximum Operating Temperature: + 130 C
• Minimum Operating Temperature: - 25 C
• Output Power: 259 W
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: SP000366360

After entering Active Burst Mode, a burst flag is set and
the internal bias is switched off in order to reduce the
current consumption of the IC to approx. 500uA.
It needs the application to enforce the VCC voltage
above the Undervoltage Lockout level of 10.5V such
that the Startup Cell will not be switched on
accidentally. Or otherwise the power loss will increase
drastically. The minimum VCC level during Active Burst
Mode depends on the load condition and the
application. The lowest VCC level is reached at no load
condition.
3.7.2.2
After entering the Active Burst Mode, the FB voltage
rises as V
inactive PWM section. The comparator C6a monitors
the FB signal. If the voltage level is larger than 3.6V, the
internal circuit will be activated; the Internal Bias circuit
resumes and starts to provide switching pulse. In
Active Burst Mode the gate G10 is released and the
current limit is reduced to 0.26V. In one hand, it can
reduce the conduction loss and the other hand, it can
reduce the audible noise. If the load at V
unchanged, the FB signal will drop to 3.1V. At this level
the C6b deactivates the internal circuit again by
switching off the internal Bias. The gate G11 is active
again as the burst flag is set after entering Active Burst
Mode. In Active Burst Mode, the FB voltage is changing
like a saw tooth between 3.1V and 3.6V (see figure 17).
3.7.2.3
The FB voltage will increase immediately if there is a
high load jump. This is observed by the comparator C4.
As the current limit is appr. 26% during Active Burst
Mode, a certain load jump is needed so that the FB
signal can exceed 4.5V. At that time the comparator C4
resets the Active Burst Mode control which in turn
blocks the comparator C12 by the gate G10. The
maximum current can then be resumed to stabilize
V
Version 2.0
OUT.
OUT
Working in Active Burst Mode
Leaving Active Burst Mode
starts to decrease, which is due to the
OUT
is still kept
16
Figure 24
1.22V
500uA
0.26V
4.5V
3.6V
3.1V
Blanking Timer
4mA
1.0V
V
V
V
10.0V
I
V
VCC
OUT
FB
VCC
CS
20ms Blanking Time
Current limit level
during Active Burst
Mode
Max. Ripple < 1%
Signals in Active Burst Mode
Entering
Active Burst
Mode
Functional Description
Leaving
Active Burst
Mode
ICE3BR0665JF
CoolSET
11 Sep 2008
®
-F3R
t
t
t
t
t
t