M95M01-RMN6P STMicroelectronics, M95M01-RMN6P Datasheet - Page 10

• Manufacturer Part Number: M95M01-RMN6P
• Description: IC EEPROM 1MBIT 5MHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M95M01-RMN6P

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 1M (128K x 8)
• Speed: 5MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Density: 1Mb
• Interface Type: Serial (SPI)
• Organization: 128Kx8
• Access Time (max): 80ns
• Frequency (max): 5MHz
• Write Protection: Yes
• Data Retention: 40Year
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Package Type: SOIC N
• Operating Temp Range: -40C to 85C
• Supply Current: 5mA
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8616-5; M95M01-RMN6P

Connecting to the SPI bus
3
10/41
Connecting to the SPI bus
These devices are fully compatible with the SPI protocol.
All instructions, addresses and input data bytes are shifted in to the device, most significant
bit first. The Serial Data Input (D) is sampled on the first rising edge of the Serial Clock (C)
after Chip Select (S) goes low.
All output data bytes are shifted out of the device, most significant bit first. The Serial Data
Output (Q) is latched on the first falling edge of the Serial Clock (C) after the instruction
(such as the Read from Memory Array and Read Status Register instructions) have been
clocked into the device.
Figure 4.
1. The Write Protect (W) and Hold (HOLD) signals should be driven high or low as appropriate.
Figure 4
Only one device is selected at a time, so only one device drives the Serial Data Output (Q)
line at a time, the other devices are high impedance.
The pull-up resistor R (represented in
master leaves the S line in the high impedance state.
In applications where the bus master might enter a state where the whole input/output SPI
bus is high-impedance at a given time (for example, if the bus master is reset during the
transmission of an instruction), the clock line (C) must be connected to an external pull-
down resistor so that, if all inputs/outputs become high impedance, the C line is pulled low
(while the S line is pulled high). This ensures that S and C do not become high at the same
time, and so, that the t
SPI Interface with
(CPOL, CPHA) =
CS3
(0, 0) or (1, 1)
SPI Bus Master
CS2 CS1
shows an example of three memory devices connected to an MCU, on an SPI bus.
Bus master and memory devices on the SPI bus
SDO
SDI
SCK
R
SHCH
R
requirement is met. The typical value of R is 100 k.
C Q D
S
Doc ID 13264 Rev 7
SPI Memory
Device
W
Figure
V
CC
HOLD
V
R
4) ensures that no device is selected if the bus
SS
C Q D
S
SPI Memory
Device
W
V
HOLD
CC
V
R
SS
M95M01-R, M95M01-W
C Q D
S
SPI Memory
Device
W
V
CC
HOLD
AI12836b
V
SS
V
V
CC
SS