M29W200BB90N6 STMicroelectronics, M29W200BB90N6 Datasheet
![IC FLASH 2MBIT 90NS 48TSOP](/photos/7/26/72669/497-48-tsop_series_sml.jpg)
M29W200BB90N6
Specifications of M29W200BB90N6
Available stocks
Related parts for M29W200BB90N6
M29W200BB90N6 Summary of contents
Page 1
... Manufacturer Code: 0020h – Top Device Code M29W200BT: 0051h – Bottom Device Code: M29W200BB 0057h ® ECOPACK PACKAGES AVAILABLE September 2005 2 Mbit (256Kb x8 or 128Kb x16, Boot Block) Low Voltage Single Supply Flash Memory TSOP48 ( 20mm Figure 1. Logic Diagram A0-A16 RP M29W200BT M29W200BB ...
Page 2
... Read mode where it can be read in the same way as a ROM or EPROM. The M29W200B is fully backward compatible with the M29W200. The memory is divided into blocks that can be erased independently possible to preserve valid data while old data is erased. Each block can be protected independently to prevent accidental Program or Erase commands from modifying the memory ...
Page 3
... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi- tions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant qual- ity documents. ...
Page 4
... Byte/Word Organization Select (BYTE). The Byte/ Word Organization Select pin is used to switch be- tween the 8-bit and 16-bit Bus modes of the mem- ory. When Byte/Word Organization Select is Low the memory is in 8-bit mode, when it is High the memory is in 16-bit mode Supply Voltage ...
Page 5
... Disable, Standby and Automatic Standby. See Tables 5 and 6, Bus Operations, for a summary. Typically glitches of less than 5ns on Chip Enable or Write Enable are ignored by the memory and do not affect bus operations. Bus Read. Bus Read operations read from the memory cells, or specific registers in the Com- mand Interface ...
Page 6
... Code can be read using a Bus Read operation with and may be set to either V Code for STMicroelectronics is 0020h. The Device Code can be read using a Bus Read operation with address bits may be set to either V Device Code for the M29W200BT is 0051h and for the M29W200BB is 0057h. ...
Page 7
... Program, Unlock Bypass Program, Chip Erase, Block Erase. After these commands read the Status Register until the Program/Erase Controller completes and the memory returns to Read Mode. Add additional Blocks during Block Erase Command with additional Bus Write Operations until Timeout Bit is set. ...
Page 8
... Once the Unlock Bypass command has been is- sued the memory will only accept the Unlock By- pass Program command and the Unlock Bypass Reset command. The memory can be read Read mode. Unlock Bypass Program Command. The lock Bypass Program command can be used to program one address in memory at a time ...
Page 9
... Reading from blocks that are being erased will output the Status Register also possible to enter the Auto Select mode: the memory will behave as in the Auto Select mode on all blocks until a Read/Reset command returns the memory to Erase Suspend mode. ...
Page 10
... DQ5 at ’1’. In both cases, a succes- sive Bus Read operation will show the bit is still ’0’. One of the Erase commands must be used to set all the bits in a block or in the whole memory from ’0’ to ’1’. DQ7 ...
Page 11
... Bus Read operations from addresses within the blocks being erased. Bus Read operations to ad- dresses within blocks not being erased will output the memory cell data Read mode. After an Erase operation that causes the Error Bit to be set the Alternative Toggle Bit can be used to ...
Page 12
M29W200BT, M29W200BB Table 11. AC Measurement Conditions Parameter V Supply Voltage CC Load Capacitance ( Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages Figure 6. AC Testing Input Output Waveform 3V 0V ...
Page 13
Table 13. DC Characteristics ( 70°C or –40 to 85°C) A Symbol Parameter I Input Leakage Current LI I Output Leakage Current LO I Supply Current (Read) CC1 I Supply Current (Standby) CC2 (1) Supply Current (Program/Erase) ...
Page 14
M29W200BT, M29W200BB Table 14. Read AC Characteristics ( 70°C or –40 to 85°C) A Symbol Alt t t Address Valid to Next Address Valid AVAV Address Valid to Output Valid AVQV ACC Chip Enable ...
Page 15
Table 15. Write AC Characteristics, Write Enable Controlled ( 70°C or –40 to 85°C) A Symbol Alt t t Address Valid to Next Address Valid AVAV Chip Enable Low to Write Enable Low ELWL ...
Page 16
M29W200BT, M29W200BB Table 16. Write AC Characteristics, Chip Enable Controlled ( 70°C or –40 to 85°C) A Symbol Alt t t Address Valid to Next Address Valid AVAV Write Enable Low to Chip Enable ...
Page 17
Table 17. Reset/Block Temporary Unprotect AC Characteristics ( 70°C or –40 to 85°C) A Symbol Alt (1) t PHWL RP High to Write Enable Low, Chip Enable t t PHEL RH Low, Output Enable Low (1) t ...
Page 18
... Note: The last two characters of the ordering code may be replaced by a letter code for preprogrammed parts, otherwise devices are shipped from the factory with the memory content bits erased to ’1’. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de- vice, please contact the ST Sales Office nearest to you ...
Page 19
Table 19. TSOP48 - 48 lead Plastic Thin Small Outline 20mm, Package Mechanical Data Symbol Typ A A1 0.100 A2 1.000 B 0.220 12.000 E 20.000 E1 18.400 e 0.500 L 0.600 L1 0.800 a ...
Page 20
M29W200BT, M29W200BB Table 20. SO44 - 44 lead Plastic Small Outline, 525 mils body width, Package Mechanical Data Symbol Typ 2.30 b 0. 28.20 E 13.30 EH 16.00 e 1.27 L 0.80 a ...
Page 21
Table 21. Revision History Revision Date Number July 1999 03/30/00 07/28/00 19-Sep-2005 4.0 Revision Details First Issue Status Register bit DQ5 clarification Data Polling Flowchart diagram change (Figure 4) Data Toggle Flowchart diagram change (Figure 5) Program/Erase Times Maximum specification ...
Page 22
... No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics ...