CAT28F010G12 ON Semiconductor, CAT28F010G12 Datasheet - Page 9

• Manufacturer Part Number: CAT28F010G12
• Description: IC FLASH 1MBIT 120NS 32PLCC
• Manufacturer: ON Semiconductor

Specifications of CAT28F010G12

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 1M (128K x 8)
• Speed: 120ns
• Interface: Parallel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 32-PLCC
• Density: 1Mb
• Access Time (max): 120ns
• Interface Type: Parallel
• Boot Type: Not Required
• Address Bus: 17b
• Operating Supply Voltage (typ): 5V
• Operating Temp Range: 0C to 70C
• Package Type: PLCC
• Program/erase Volt (typ): 11.4 to 12.6V
• Sync/async: Asynchronous
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Word Size: 8b
• Number Of Words: 128K
• Supply Current: 30mA
• Mounting: Surface Mount
• Pin Count: 32
• Data Bus Width: 8 bit
• Architecture: Non Sectored
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Maximum Operating Current: 30 mA
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: CAT28F010G-12; CAT28F010G-12

WRITE OPERATIONS
The following operations are initiated by observing the
sequence specified in the Write Command Table.
Read Mode
The device can be put into a standard READ mode by
initiating a write cycle with 00H on the data bus. The
subsequent read cycles will be performed similar to a
standard EPROM or E
Figure 4. A.C. Timing for Erase Operation
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
ADDRESSES
DATA (I/O)
WE (W)
OE (G)
CE (E)
V CC POWER-UP
V CC
V PP
& STANDBY
5.0V
0V
V PPH
V PPL
t GHWL
HIGH-Z
2
SETUP ERASE
PROM Read.
COMMAND
t VPEL
t DS
t WC
t CH
t WP
t CS
t WPH
DATA IN
= 20H
COMMAND
t DH
ERASE
t DS
t WC
DATA IN
= 20H
t WP
ERASING
t CH
t DH
9
t AS
t CS
t WHWH2
Signature Mode
An alternative method for reading device signature (see
Read Operations Signature Mode), is initiated by writing
the code 90H into the command register while keeping
V
OE low (and WE high) will output the device signature.
A Read cycle from address 0001H retrieves the binary
code for the device on outputs I/O
PP
ERASE VERIFY
COMMAND
t WP
high. A read cycle from address 0000H with CE and
t DS
t WC
CATALYST Code = 00110001 (31H)
28F010 Code = 1011 0100 (B4H)
t AH
DATA IN
= A0H
t DH
t CH
t WHGL
t OLZ
t OE
t LZ
t CE
VERIFICATION
ERASE
t RC
DATA OUT
0
VALID
to I/O
V CC POWER-DOWN/
Doc. No. MD-1019, Rev. G
CAT28F010
7
STANDBY
t EHQZ
t DF
.
t OH
28F010 F11