HV9930DB1 Supertex, HV9930DB1 Datasheet

no-image

HV9930DB1

Manufacturer Part Number
HV9930DB1
Description
LED Lighting Development Tools HV9930 Demo Board
Manufacturer
Supertex
Datasheet

Specifications of HV9930DB1

Product Category
LED Lighting Development Tools
Product
Demonstration Boards
Core
HV9930
Operating Supply Voltage
9 V to 16 V
Factory Pack Quantity
1
For Use With
7 - 1 W LEDs
General Description
The HV9930DB1 is an LED driver demoboard capable of
driving up to 7 1-watt LEDs in series from an automotive
input of 9 - 16VDC. The demoboard uses Supertex’s
HV9930 in a boost-buck topology. The converter operates
at frequencies in excess of 300kHz and has excellent
output current regulation over the input voltage range. It
can also withstand transients up to 42V and operate down
to 6V input. The converter is also protected against open
LED and output short circuit conditions. Protection against
reverse polarity up to 20V is also included.
Board Layout and Connection Diagram
Connections:
Input -
connector J1 as shown in the Connection Diagram.
Output -
connector J2 as shown.
Enable/PWM Dimming:
To just enable the board, short pins 1 and 2 of connector J3
as shown. For PWM dimming, connect the external push-pull
Supertex inc.
The input is connected between the terminals of
The output is connected between the terminals of
Supertex inc.
Actual Size: 2.25” x 1.25”
High Bright LED Driver IC Demoboard
Meeting Automotive Requirements
1235 Bordeaux Drive, Sunnyvale, CA 94089
Dimming
PWM
V
IN
Enable
+
+
-
Specifications
Parameter
Input voltage (steady state):
Input voltage (transient):
Output LED string voltage:
Output current:
Output current ripple:
Switching frequency:
Efficiency:
Open LED protection:
Output short circuit protection:
Reverse polarity protection:
Input current limit:
PWM dimming frequency:
Conducted EMI:
square wave source between terminals 1 and 3 of connector
J3 as shown by the dotted lines.
Note:
During PWM dimming, pin 2 of connector J3 should be left
open. Also, the PWM signal must have the proper polarity
with the positive connected to pin 1 of J3. Note that pin 3
of J3 is internally connected to the return path of the input
voltage.
_
+
Tel: 408-222-8888
www.supertex.com
conducted EMI standards
Included; limits current at
Included; clamps output
HV9930DB1
430kHz (13.5V input)
500kHz (16.0V input)
80% (at 13.5V input)
300kHz (9.0V input)
Meets SAE J1113
9.0VDC - 16VDC
voltage at 33V
350mA +/-5%
Up to 1.0kHz
_
+
5% typical
-20V max
28V max
42VDC
350mA
Value
1.9A

Related parts for HV9930DB1

HV9930DB1 Summary of contents

Page 1

... Supertex inc. High Bright LED Driver IC Demoboard Meeting Automotive Requirements General Description The HV9930DB1 is an LED driver demoboard capable of driving 1-watt LEDs in series from an automotive input 16VDC. The demoboard uses Supertex’s HV9930 in a boost-buck topology. The converter operates at frequencies in excess of 300kHz and has excellent output current regulation over the input voltage range ...

Page 2

... PWM dimming ratios can be obtained at lower frequencies like 100 or 200Hz Typical Results Fig. 1 shows the efficiency plot for the HV9930DB1 over the input voltage range. The converter has efficiencies greater than 80% over 13V input. Note that these measurements do not include the 0.3 - 0.5W loss in the reverse blocking diode ...

Page 3

... It can be seen that the LED current drops briefly when the input voltage jumps, but there are no overshoots. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 3 HV9930DB1 Fig. 5. Cold Crank Operation Channel 1 (blue): Input voltage (10V/div) Channel 3 (pink): Input current (1A/div) Channel 4 (green): LED current; 100mA/div Fig ...

Page 4

... Fig. 7a shows the operation of the converter during an Open LED condition and Fig. 7b shows the operation during output short circuit condition. In both cases, it can be seen that the HV9930DB1 can easily withstand faults and come back into normal operation almost instantly. Fig. 7 HV9930DB1 during output fault conditions FET drain voltage (20V/div) Channel 1 in (a) ...

Page 5

... The table also lists the Class of the SAE standard the board meets in each frequency range. The conducted EMI plots for the HV9930DB1 obtained at an input voltage of 13.5V and an LED string voltage of 27V (output current is 350mA) are given in the Appendix. ...

Page 6

... Circuit Schematic: Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 6 HV9930DB1 ● Tel: 408-222-8888 ● www.supertex.com ...

Page 7

... PCB Top Layer PCB Bottom Layer Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 7 HV9930DB1 ● Tel: 408-222-8888 ● www.supertex.com ...

Page 8

... Appendix – Conducted EMI Test Results Supertex inc. Ref. Level = 70dBµV Ref. Level = 50dBµV Ref. Level = 45dBµV ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 8 HV9930DB1 ● Tel: 408-222-8888 ● www.supertex.com ...

Page 9

... Appendix – Conducted EMI Test Results Supertex inc. (cont.) Ref. Level = 65dBµV Ref. Level = 49dBµV ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 9 HV9930DB1 ● Tel: 408-222-8888 ● www.supertex.com ...

Page 10

... SMD0805 Yageo SMD1206 Yageo SMD0805 Yageo SMD0805 Yageo SO-8 Supertex does not assume responsibility for use of devices described, and limits its liability Supertex inc. Supertex inc. 10 HV9930DB1 Manufacturer’s Part # C1210C224K5RACTU ECJ-4YB1E475K GRM32ER71H475KA88L C0805C105K4RACTU C2012X7R1C225K 08052R104K9B20D B220-13 BZX84C33-7 1N4148W-7 B2100-13 S2B-EH S3B-EH ...

Related keywords