TRK-USB-MPC5643L Freescale Semiconductor, TRK-USB-MPC5643L Datasheet - Page 133

• Manufacturer Part Number: TRK-USB-MPC5643L
• Description: Development Boards & Kits - Other Processors StarTrakMiniUSG MPC5643L
• Manufacturer: Freescale Semiconductor

Specifications of TRK-USB-MPC5643L

• Rohs: yes
• Product: Starter Kits
• Tool Is For Evaluation Of: MPC5643L
• Core: Five Stage Pipeline
• Interface Type: LIN, DSPI
• Operating Supply Voltage: 3 V to 3.6 V
• Data Bus Width: 32 bit, 64 bit
• Description/function: Starter Kit for MPC5643L
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• For Use With: MPC5643L

Freescale Semiconductor
Revision
8
27 April 2012 Editorial changes.
Date
In the “Device comparison” section, changed “Ambient temperature range using external
In the “Block diagram” section, removed one PMU from the figure.
In the 257-pin pinout figure, changed cut2 to cut2/3 in Notes.
In the pin function summary table, changed cut2 to cut2/3.
In the “System pins” table:
In the pin-muxing table:
In the “Absolute maximum ratings” table:
In the “Recommended operating conditions” table, removed the “V
In the “Thermal characteristics” section:
In the “Supply current characteristics“ table:
In the “FMPLL electrical characteristics” table:
In the “ADC conversion characteristics” table:
In the “Temperature sensor electrical characteristics“ table, for T
In the “Input Impedance and ADC Accuracy“ section:
• Added Note regarding Open Drain Enable.
• Added description to RESET pin.
• Added Note about Open Drain.
• Changed cut2 to cut2/3.
• Changed all entries of column 'Weak pull config during reset’ to ' - ' , except for PCR[2],
• Removed the “V
• Added the footnote “Internal structures hold the input voltage...” to the V
• Added the “Thermal characteristics for 100 LQFP package“ table.
• Updated values and footnote 1 in the 144 package table.
• Updated footnote 1 in the 257 package table.
• Added footnote 1 to parameter “I
• Changed “I
• Changed “I
• Deleted the footnote “This value is true when operating at frequencies above 60 MHz...”
• Changed “f
• Revised the entry for TUE
• Revised the entry for TUE
• Changed C
• Changed R
• Removed R
• Changed the C
• In the “ADC conversion characteristics“ table, changed INL Min/Max values from -2/+2
ballast transistor (BGA)“ from TBD to “–40 to 125 °C“.
PCR[3], PCR[4] and PCR[21].
specifications.
from the specification for f
specifications.
T and “Total unadjusted error for IS1WINJ (single ADC channels)”).
“Total unadjusted error for IS1WWINJ (double ADC channels)”).
Min/Max from values -7/+7 to -10/+10.
the sentence immediately preceding it.
to -3/+3.
MPC5643L Microcontroller Data Sheet, Rev. 8.1
Table 41. Revision history (continued)
DD_LV_STOP
DD_LV_HALT
SYS
S
eq
L
, R
in the text from 3 pF to 7.5 pF.
in the text from 330 k to 133 k.
” to “f
F
SW
SS_HV_REG
constraint value equation constant from 2048 to 8192.
, and R
FMPLLOUT
” at 150C from 72mA to 80mA.
” at 150C from 80mA to 72mA.
IS1WINJ
AD
CS
IS1WWINJ
” row.
from the external network design constraint equation and
Description of changes
and f
” in the entries for the C
DD_LV_TYP
(was P/T and “Total unadjusted error for IS1WINJ”, is
DS
(was “Total unadjusted error for IS1WWINJ”, is
.
+ I
DD_LV_PLL
JITTER
“ (symbol “T”).
, f
J
LCK
= T
Document revision history
SS_HV_REG
A
, f
to 125 °C, changed
UL
, f
CS
IN
, and f
maximum
” row.
DS
133