SST89E554RC-40-C-PI Microchip Technology, SST89E554RC-40-C-PI Datasheet - Page 40

• Manufacturer Part Number: SST89E554RC-40-C-PI
• Description: 8-bit Microcontrollers - MCU 32KB+8KB 40ns
• Manufacturer: Microchip Technology

Specifications of SST89E554RC-40-C-PI

• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 1 KB
• On-chip Adc: No
• Operating Supply Voltage: 4.5 V to 5.5 V
• Package / Case: PDIP-40
• Mounting Style: Through Hole
• Data Rom Size: 128 B
• Interface Type: SPI, UART
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• On-chip Dac: No
• Processor Series: FlashFlex
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 4.5 V

EOL Data Sheet
4.2.4.4 Byte-Program
The Byte-Program command programs data into a single
byte. The address is determined by the contents of SFAH
and SFAL. The data byte is in SFDT.
4.2.4.5 Byte-Verify
The Byte-Verify command allows the user to verify that the
device has correctly performed an Erase or Program com-
mand. Byte-Verify command returns the data byte in SFDT
if the command is successful. The user is required to check
that the previous flash operation has fully completed before
issuing a Byte-Verify. Byte-Verify command execution time
is short enough that there is no need to poll for command
completion and no interrupt is generated.
©2007 Silicon Storage Technology, Inc.
operation completion
MOV SFCM, #0EH
SFST[2] indicates
Polling scheme
MOV SFAH, #byte_addressH
MOV SFAL, #byte_addressL
Program byte address
Move data to SFDT
MOV SFDT, #data
ORL SFCF, #40H
IAP Enable
indicates completion
MOV SFCM, #8EH
Interrupt scheme
INT1 interrupt
1207 F46.1
40
4.2.4.6 Prog-SB3, Prog-SB2, Prog-SB1
Prog-SB3, Prog-SB2, Prog-SB1 commands are used to
program the security bits (see Table 9-1). Completion of
any of these commands, the security options will be
updated immediately.
Security bits previously in un-programmed state can be
programmed by these commands. Prog-SB3, Prog-SB2
and Prog-SB1 commands should only reside in Block 1 or
external code memory.
MOV SFCM, #0FH
MOV SFCM, #8FH
Program SB1
or
indicates completion
SST89E564RD / SST89V564RD
SST89E554RC / SST89V554RC
Polling SFST[2]
MOV SFAH, #byte_addressH
MOV SFAL, #byte_addressL
OR
Program byte address
MOV SFCM, #0CH
ORL SFCF, #40H
SFDT register
contains data
MOV SFDT, #0AAH
MOV SFCM, #03H
MOV SFCM, #83H
IAP Enable
ORL SFCF, #40H
Program SB2
IAP Enable
Set-Up
or
indicates completion
FlashFlex MCU
INT1# Interrupt
1207 F47.0
OR
S71207-08-EOL
MOV SFCM, #05H
MOV SFCM, #85H
Program SB3
or
1207 F48.0
1/07