CY62128EV30LL-45ZXI Cypress Semiconductor Corp, CY62128EV30LL-45ZXI Datasheet - Page 8

• Manufacturer Part Number: CY62128EV30LL-45ZXI
• Description: IC SRAM 1MBIT 45NS 32TSOP
• Manufacturer: Cypress Semiconductor Corp
• Type: Asynchronousr

Specifications of CY62128EV30LL-45ZXI

• Memory Size: 1M (128K x 8)
• Package / Case: 32-TSOP I
• Format - Memory: RAM
• Memory Type: SRAM
• Speed: 45ns
• Interface: Parallel
• Voltage - Supply: 2.2 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Access Time: 45 ns
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.2 V
• Maximum Operating Current: 16 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Number Of Ports: 1
• Operating Supply Voltage: 2.5 V, 3.3 V
• Density: 1Mb
• Access Time (max): 45ns
• Sync/async: Asynchronous
• Architecture: Not Required
• Clock Freq (max): Not RequiredMHz
• Operating Supply Voltage (typ): 3V
• Address Bus: 17b
• Package Type: TSOP-I
• Operating Temp Range: -40C to 85C
• Supply Current: 16mA
• Operating Supply Voltage (min): 2.2V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Word Size: 8b
• Number Of Words: 128K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 428-2067; CY62128EV30LL-45ZXI

Switching Waveforms
Truth Table
Notes
Document #: 38-05579 Rev. *I
26. CE is the logical combination of CE
27. The internal write time of the memory is defined by the overlap of WE, CE = V
28. Data I/O is high impedance if OE = V
29. If CE
30. During this period, the I/Os are in output state. Do not apply input signals.
31. The ‘X’ (Don’t care) state for the Chip enables in the truth table refer to the logic state (either HIGH or LOW). Intermediate voltage levels on these pins is not permitted.
ADDRESS
ADDRESS
CE
a write by going INACTIVE. The data input setup and hold timing should be referenced to the edge of the signal that terminates the write.
X
DATA I/O
DATA I/O
H
L
L
L
[31]
1
1
goes HIGH or CE
WE
WE
CE
CE
CE
X
H
H
H
L
[31]
2
NOTE 30
2
goes LOW simultaneously with WE HIGH, the output remains in high impedance state.
WE
t
SA
X
X
H
H
L
1
Figure 9. Write Cycle No. 2 CE1 or CE2 controlled
(continued)
and CE
IH
Figure 10. Write Cycle No. 3 WE controlled, OE LOW
.
t
HZWE
OE
2
X
X
X
H
L
. When CE
t
SA
1
is LOW and CE
Inputs/Outputs
t
AW
t
Data out
AW
Data in
High Z
High Z
High Z
t
SCE
t
2
t
WC
WC
t
is HIGH, CE is LOW; when CE
PWE
IL
. All signals must be ACTIVE to initiate a write and any of these signals can terminate
t
PWE
t
DATA VALID
DATA VALID
t
SCE
SD
t
Selected, outputs disabled
SD
Deselect/power-down
Deselect/power-down
Mode
Read
Write
[26, 27, 28, 29]
1
is HIGH or CE
[26, 29]
t
HD
t
t
HA
LZWE
CY62128EV30 MoBL
t
HA
t
HD
2
is LOW, CE is HIGH.
Standby (I
Standby (I
Active (I
Active (I
Active (I
Power
Page 8 of 15
CC
CC
CC
SB
SB
)
)
)
)
)
®
[+] Feedback