M24512-WMN6TP STMicroelectronics, M24512-WMN6TP Datasheet - Page 17

• Manufacturer Part Number: M24512-WMN6TP
• Description: IC EEPROM 512KBIT 400KHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M24512-WMN6TP

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 512K (64K x 8)
• Speed: 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Density: 512Kb
• Interface Type: Serial (I2C)
• Organization: 64Kx8
• Access Time (max): 900ns
• Frequency (max): 400KHz
• Write Protection: Yes
• Data Retention: 40Year
• Operating Supply Voltage (typ): 3.3/5V
• Operating Temp Range: -40C to 85C
• Supply Current: 5mA
• Operating Supply Voltage (min): 2.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8626-2; M24512-WMN6TP

M24512-R, M24512-W, M24512-DR
3.10
3.11
3.12
Write Identification Page (M24512-DR only)
The Identification Page (128 bytes) is an additional page which can be written and (later)
permanently locked in Read-only mode. The identification page is written by issuing an
Write Identification Page instruction. This instruction uses the same protocol and format as
Page Write (into memory array), except for the following differences:
●
●
LSB address bits A6/A0 define the byte address inside the identification page.
If the Identification page is locked, the data bytes transferred during the Write Identification
Page instruction are not acknowledged (NoAck).
Lock Identification Page (M24512-DR only)
The Lock Identification Page instruction (Lock ID) permanently locks the Identification page
in read-only mode. The Lock ID instruction is similar to Byte Write (into memory array) with
the following specific conditions:
●
●
●
If the Identification Page is locked, the data bytes transferred during the ID Write instruction
are not acknowledged (NoAck).
ECC (error correction code) and write cycling
The M24512-x devices offer an ECC (error correction code) logic which compares each 4-
byte word with its six associated ECC EEPROM bits. As a result, if a single bit out of 4 bytes
of data happens to be erroneous during a Read operation, the ECC detects it and replaces
it by the correct value. The read reliability is therefore much improved by the use of this
feature.
Note however that even if a single byte has to be written, 4 bytes are internally modified
(plus the ECC bits), that is, the addressed byte is cycled together with the other three bytes
making up the word. It is therefore recommended to write by word (4 bytes) at address 4*N
(where N is an integer) in order to benefit from the larger amount of Write cycles.
The M24512-x devices are qualified at 1 million (1 000 000) Write cycles, using a cycling
routine that writes to the device by multiples of 4-bytes.
Device type identifier = 1011b
MSB address bits A15/A7 are don't care except for address bit A10 which must be ‘0’.
Device Type Identifier = 1011b
Address bit A10 must be ‘1’; all other address bits are don't care
The data byte must be equal to the binary value xxxx xx1x, where x is don't care.
Doc ID 16459 Rev 22
Device operation
17/41