BR24L64F-WE2 Rohm Semiconductor, BR24L64F-WE2 Datasheet - Page 7
![IC EEPROM 64KBIT 400KHZ 8SOP](/photos/7/22/72233/br24l64f-we2_sml.jpg)
BR24L64F-WE2
Manufacturer Part Number
BR24L64F-WE2
Description
IC EEPROM 64KBIT 400KHZ 8SOP
Manufacturer
Rohm Semiconductor
Specifications of BR24L64F-WE2
Memory Size
64K (8K x 8)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOP
Clock Frequency
400kHz
Supply Voltage Range
1.8V To 5.5V
Memory Case Style
SOP
No. Of Pins
8
Operating Temperature Range
-40°C To +85°C
Svhc
No SVHC (18-Jun-2010)
Package /
RoHS Compliant
Organization
8 Kbit x 8
Interface Type
I2C
Maximum Clock Frequency
0.1 MHz
Access Time
3500 ns
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Maximum Operating Current
3 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
1.8 V, 5.5 V
Memory Configuration
8K X 8
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
BR24L64F-WE2
BR24L64F-WE2TR
BR24L64F-WE2TR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
BR24L64F-WE2
Manufacturer:
ROMH
Quantity:
2 296
Part Number:
BR24L64F-WE2
Manufacturer:
ROHM/罗姆
Quantity:
20 000
●I
2
○I
○Start condition (Start bit recognition)
○Stop condition (stop bit recongnition)
○Acknowledge (ACK) signal
○Device addressing
C BUS communication
・Before executing each command, start condition (start bit) where SDA goes from
・This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this confdition is
・Each command can be ended by SDA rising from
・This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In master
・The device (this IC at slave address input of write command, read command, and μ-COM at data output of read
・This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal)
・Each write action outputs acknowledge signal (ACK signal)
・Each read action outputs 8bit data (read data), and detects acknowledge signal (ACK signal) 'LOW'.
・When acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (μ-COM) side, this IC
・Output slave address after start condition from master.
・The significant 4 bits of slave address are used for recognizing a device type. The device code of this IC is fixed to
・Next slave addresses (A2 A1 A0 --- device address) are for selecting devices, and plural ones can be used on a same bus
・The most insignificant bit (R/W --- READ / WRITE) of slave address is used for designating write or read action, and is as
I
acknowledge is always required after each byte. I
communication lines of serial data (SDA) and serial clock (SCL).
Among devices, there are “master” that generates clock and control communication start and end, and “slave” that is
controlled by address peculiar to devices. EEPROM becomes “slave”. And the device that outputs data to bus during data
communication is called “transmitter”, and the device that receives data is called “receiver”.
2
2
Note) Up to 4 units BR24L04-W, up to 2 units of BR24L08-W, and one unit of BR24L16-W can be connected.
and slave, the device (μ-COM at slave address input of write command, read command, and this IC at data output of read
command) at the transmitter (sending) side releases the bus after output of 8bit data.
command) at the receiver (receiving) side sets SDA
signal) showing that it has received the 8bit data.
continues data output. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and recognizes
stop cindition (stop bit), and ends read action. And this IC gets in status.
according to the number of device addresses.
shown below.
C BUS data communication
C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long, and
'
satisfied, any command is executed.
PS, P0~P2 are page select bits.
HIGH
BR24L01A-W
BR24L02-W
BR24L04-W
BR24L08-W
BR24L16-W
BR24L32-W
BR24L64-W
Device address is set by 'H' and 'L' of each pin of A0, A1, and A2.
'
Type
is necessary.
Setting R / W to 0 ------- write (setting 0 to word address setting of random read)
Setting R / W to 1 ------- read
1
1
1
1
1
1
1
SDA
SCL
0
0
0
0
0
0
0
1
1
1
1
1
1
1
START
condition
S
0
0
0
0
0
0
0
ADDRESS
Slave address
A2
A2
A2
A2
P2
A2
A2
1-7
A1
A1
A1
P1
P1
A1
A1
R/W
8
Fig.35 Data transfer timing
ACK
9
A0
A0
PS
P0
P0
A0
A0
2
C BUS carries out data transmission with plural devices connected by 2
'
LOW
1-7
R/W
R/W
R/W
R/W
R/W
R/W
R/W
DATA
'
LOW
7/32
'
to
8
Maximum number of
'
'
'
HIGH
connected buses
during 9 clock cycles, and outputs acknowledge signal (ACK
LOW
ACK
9
'
'
, at receiving 8bit data (word address and write data).
8
8
4
2
1
8
8
when stop condition (stop bit), namely, SCL is
1-7
DATA
8
ACK
9
condition
'
STOP
HIGH
GND
P
A0
A1
A2
'
1
2
3
4
down to
BR24L01A-W
BR24L02-W
BR24L04-W
BR24L08-W
BR24L16-W
BR24L32-W
BR24L64-W
'
LOW
'
'
when SCL is
LOW
8
7
5
6
Vcc
WP
SCL
SDA
'
'
HIGH
.
'
1010
'
'
.