72V3644L10PF IDT, 72V3644L10PF Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
72V3644L10PF
Manufacturer Part Number
72V3644L10PF
Description
FIFO
Manufacturer
IDT
Datasheet
1.72V3644L15PF.pdf
(34 pages)
Specifications of 72V3644L10PF
Part # Aliases
IDT72V3644L10PF
PIN DESCRIPTIONS
IDT72V3624/72V3634/72V3644 3.3V CMOS SyncBiFIFO
256 x 36 x 2, 512 x 36 x 2, 1,024 x 36 x 2
ENA
ENB
FFA/IRA
FFB/IRB
Symbol
A0-A35
AEA
AEB
AFA
AFB
B0-B35
BE/FWFT
BM
CLKA
CLKB
CSA
CSB
EFA/ORA
EFB/ORB
Port A Data
Port A Almost-
Empty Flag
Port B Almost-
Empty Flag
Port A Almost-
Full Flag
Port B Almost-
Full Flag
Port A Data
Big-Endian/
First Word
Fall Through
Select
Bus-Match
Select
(Port B)
Port A Clock
Port B Clock
Port A Chip
Select
Port B Chip
Select
Port A Empty/
Output Ready
Flag
Port B Empty/
Output Ready
Flag
Port A Enable
Port B Enable
Port A Full/
Input Ready
Flag
Port B Full/
Input Ready
Flag
Name
I/O
I/O
I/O
O
O
O
O
O
O
O
O
I
I
I
I
I
I
I
I
36-bit bidirectional data port for side A.
Programmable Almost-Empty flag synchronized to CLKA. It is LOW when the number of words in FIFO2 is
less than or equal to the value in the Almost-Empty A Offset register, X2.
Programmable Almost-Empty flag synchronized to CLKB. It is LOW when the number of words in FIFO1 is
less than or equal to the value in the Almost-Empty B Offset register, X1.
Programmable Almost-Full flag synchronized to CLKA. It is LOW when the number of empty locations in
FIFO1 is less than or equal to the value in the Almost-Full A Offset register, Y1.
Programmable Almost-Full flag synchronized to CLKB. It is LOW when the number of empty locations in
FIFO2 is less than or equal to the value in the Almost-Full B Offset register, Y2.
36-bit bidirectional data port for side B.
This is a dual purpose pin. During Master Reset, a HIGH on BE will select Big Endian operation. In this
case, depending on the bus size, the most significant byte or word on Port A is read from Port B first
(A-to-B data flow) or written to Port B first (B-to-A data flow). A LOW on BE will select Little-Endian operation.
written to Port B first (B-to-A data flow). After Master Reset, this pin selects the timing mode. A HIGH on
FWFT selects IDT Standard mode, a LOW selects First Word Fall Through mode. Once the timing mode has
been selected, the level on FWFT must be static throughout device operation.
A HIGH on this pin enables either byte or word bus width on Port B, depending on the state of SIZE. A
LOW selects long word operation. BM works with SIZE and BE to select the bus size and endian
arrangement for Port B. The level of BM must be static throughout device operation.
CLKA is a continuous clock that synchronizes all data transfers through Port A and can be asynchronous
or coincident to CLKB. FFA/IRA, EFA/ORA, AFA, and AEA are all synchronized to the LOW-to-HIGH
transition of CLKA.
CLKB is a continuous clock that synchronizes all data transfers through Port B and can be asynchronous
or coincident to CLKA. FFB/IRB, EFB/ORB, AFB, and AEB are synchronized to the LOW-to-HIGH transition
of CLKB.
CSA must be LOW to enable to LOW-to-HIGH transition of CLKA to read or write on Port A. The A0-A35
outputs are in the high-impedance state when CSA is HIGH.
CSB must be LOW to enable a LOW-to-HIGH transition of CLKB to read or write data on Port B. The
B0-B35 outputs are in the high-impedance state when CSB is HIGH.
This is a dual function pin. In the IDT Standard mode, the EFA function is selected. EFA indicates whether
or not the FIFO2 memory is empty. In the FWFT mode, the ORA function is selected. ORA indicates the
presence of valid data on A0-A35 outputs, available for reading. EFA/ORA is synchronized to the LOW-to-
HIGH transition of CLKA.
This is a dual function pin. In the IDT Standard mode, the EFB function is selected. EFB indicates whether
or not the FIFO1 memory is empty. In the FWFT mode, the ORB function is selected. ORB indicates the
presence of valid data on the B0-B35 outputs, available for reading. EFB/ORB is synchronized to the LOW-to-
HIGH transition of CLKB.
ENA must be HIGH to enable a LOW-to-HIGH transition of CLKA to read or write data on Port A.
ENB must be HIGH to enable a LOW-to-HIGH transition of CLKB to read or write data on Port B.
This is a dual function pin. In the IDT Standard mode, the FFA function is selected. FFA indicates
whether or not the FIFO1 memory is full. In the FWFT mode, the IRA function is selected. IRA indicates
whether or not there is space available for writing to the FIFO1 memory. FFA/IRA is synchronized to the
LOW-to-HIGH transition of CLKA.
This is a dual function pin. In the IDT Standard mode, the FFB function is selected. FFB indicates whether
or not the FIFO2 memory is full. In theFWFT mode, the IRB function is selected. IRB indicates whether or
not there is space available for writing to the FIFO2 memory. FFB/IRB is synchronized to the LOW-to-HIGH
transition of CLKB.
In this case, the least significant byte or word on Port A is read from Port B first (for A-to-B data flow) or
TM
WITH BUS-MATCHING
4
Description
COMMERCIAL TEMPERATURE RANGE