TN2640LG M908 Supertex, TN2640LG M908 Datasheet
TN2640LG M908
Related parts for TN2640LG M908
TN2640LG M908 Summary of contents
Page 1
... MOS devices. Characteristic of all MOS structures, this device is free from thermal runaway and thermally induced secondary breakdown. Supertex’s vertical DMOS FETs are ideally suited to a wide range of switching and amplifying applications where very low threshold voltage, high breakdown voltage, high input impedance, low input capacitance, and fast switching speeds are desired ...
Page 2
... I GS Ω 5 10V 0. 10V mmho V = 25V 225 25V 1.0MHz 15 ● Tel: 408-222-8888 ● www.supertex.com TN2640 I I † DR DRM (A) 500 3.0 260 2.0 220 2.0 = 1.0mA = 2.0mA D = 2.0mA Max rating DS = 125 25V DS = 25V DS = 500mA D = 500mA ...
Page 3
... Bordeaux Drive, Sunnyvale, CA 94089 3 Max Units Conditions 25V 2.0A 25Ω GEN 200mA 0V 1. PULSE GENERATOR R GEN INPUT ● Tel: 408-222-8888 ● www.supertex.com TN2640 OUTPUT D.U.T. ...
Page 4
... Bordeaux Drive, Sunnyvale, CA 94089 4 Saturation Characteristics 2 10V 2.0 1.5 1.0 0 (volts) DS Power Dissipation vs. Temperature 3.0 DPAK 2.4 1.8 SO-8 1.2 TO-92 0 100 125 T (°C) A Thermal Response Characteristics 1.0 0.8 0.6 0.4 TO-92 0 25° 1.0W 0 0.001 0.01 0.1 1.0 t (seconds) p ● Tel: 408-222-8888 ● www.supertex.com TN2640 150 10 ...
Page 5
... Bordeaux Drive, Sunnyvale, CA 94089 5 On-Resistance vs. Drain Current 10V GS 0 1.0 2.0 3.0 4.0 I (amperes and R Variation with Temperature 2mA (th 10V, 0.5A DS(ON) - 100 T (°C) j Gate Drive Dynamic Characteristics 653pF V = 10V 40V DS 253pF (nanocoulombs) G ● Tel: 408-222-8888 ● www.supertex.com TN2640 5.0 2.2 1.8 1.4 1.0 0.6 0.2 150 5 ...
Page 6
... MAX .094 .005 .035 .045 JEDEC Registration TO-252, Variation AA, Issue E, June 2004. * This dimension is not specified in the JEDEC drawing. Drawings not to scale. Supertex Doc. #: DSPD-3TO252K4, Version E041309 Note Rear View Gauge Plane θ ...
Page 7
... Symbol A A1 MIN 1.35* 0.10 Dimension NOM - - (mm) MAX 1.75 0.25 JEDEC Registration MS-012, Variation AA, Issue E, Sept. 2005. * This dimension is not specified in the JEDEC drawing. Drawings are not to scale. Supertex Doc. #: DSPD-8SOLGTG, Version I041309 Note 1 Seating Plane 1.25 0.31 4.80* 5.80* 3.80 ...
Page 8
... Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship ...