ADS-947GE MURATA-PS [Murata Power Solutions Inc.], ADS-947GE Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
ADS-947GE
Manufacturer Part Number
ADS-947GE
Description
14-Bit, 10MHz Sampling A/D Converters
Manufacturer
MURATA-PS [Murata Power Solutions Inc.]
Datasheet
1.ADS-947GE.pdf
(8 pages)
TECHNICAL NOTES
1. Obtaining fully specified performance from the ADS-947
2. The ADS-947 achieves its specified accuracies without the
Footnotes:
DYNAMIC PERFORMANCE (Cont.)
S/H Acquisition Time
Overvoltage Recovery Time
A/D Conversion Rate
DIGITAL OUTPUTS
Logic Levels
Output Coding
POWER REQUIREMENTS
Power Supply Ranges
Power Supply Currents
Power Dissipation
Power Supply Rejection
requires careful attention to pc card layout and power
supply decoupling. The device’s analog and digital ground
systems are connected to each other internally. For optimal
performance, tie all ground pins (14, 19 and 24) directly to a
large analog ground plane beneath the package.
Bypass all power supplies to ground with 4.7µF tantalum
capacitors in parallel with 0.1µF ceramic capacitors. Locate
the bypass capacitors as close to the unit as possible.
need for external calibration. If required, the device’s small
initial offset and gain errors can be reduced to zero using
the adjustment circuitry shown in Figures 2 and 3.
When using this circuitry, or any similar offset and gain
calibration hardware, make adjustments following warmup.
To avoid interaction, always adjust offset before gain.
Logic "1"
Logic "0"
Logic Loading "1"
Logic Loading "0"
+5V Supply
–5.2V Supply
+5V Supply
–5.2V Supply
®
All power supplies should be on before applying a start convert pulse. All
supplies and the clock (start convert pulses) must be present during warmup
periods. The device must be continuously converting during this time.
Contact DATEL for other input voltage ranges.
A 10MHz clock with a 20ns positive pulse width is used for all production
testing. See Timing Diagram, figure 4, for more details.
( to ±0.003%FSR, 4V step)
®
–4.75
+4.75
+2.4
MIN.
10
—
—
—
—
—
—
—
—
—
+25°C
+250
–200
TYP.
–5.2
+5.0
2.0
40
—
—
—
—
—
—
—
MAX.
+5.25
–5.45
+260
–210
+0.4
±0.1
2.25
100
45
–4
+4
—
—
3
+4.75
–4.75
+2.4
MIN.
—
10
—
—
—
—
—
—
—
—
3. Applying a start convert pulse while a conversion is in
4. A passive bandpass filter is used at the input of the A/D for
SIGNAL
INPUT
Effective bits is equal to:
This is the time required before the A/D output data is valid once the analog
input is back within the specified range. This time is only guaranteed if the
input does not exceed ±2.2V (S/H saturation voltage).
The minimum supply voltages of +4.9V and –5.1V for ±V
for –40°C operation only. The minimum limits are +4.75V and –4.95V
when operating at +125°C
progress (EOC = logic 1) will initiate a new and inaccurate
conversion cycle. Data for the interrupted and subsequent
conversions will be invalid.
all production testing.
Figure 2. Optional ADS-947 Gain Adjust Calibration Circuit
0 to +70°C
+250
TYP.
–200
+5.0
–5.2
2.0
40
—
—
—
—
—
—
—
(SNR + Distortion) – 1.76 +
Offset Binary
ADJUST
GAIN
50
MAX.
+5.25
–5.45
+260
–210
+0.4
2.25
±0.1
100
45
–4
+4
—
—
1.98k
+2.4
+4.9
–4.9
MIN.
—
10
—
—
—
—
—
—
—
—
–40 to +100°C
6.02
20 log
+250
–200
TYP.
+5.0
–5.2
2.0
40
—
—
—
—
—
—
—
Actual Input Amplitude
+5V
–5V
2k
Full Scale Amplitude
ADS-947
MAX.
+5.25
–5.45
+260
–210
+0.4
2.25
±0.1
DD
100
–4
+4
45
—
—
are required
To Pin 21
of ADS-947
%FSR/%V
UNITS
Watts
Volts
Volts
Volts
Volts
MHz
mA
mA
mA
mA
ns
ns