EDS6-120 FUJI [Fuji Electric], EDS6-120 Datasheet - Page 2

• Manufacturer Part Number: EDS6-120
• Description: E SERIESE ELECTROMAGNETIC FLOWMETER(SEPARATE TYPE)
• Manufacturer: FUJI [Fuji Electric]

2
FMF1,2/FMH
• Fluid temperature :
Note 1) Materials of fluid wetted parts should be selected in
Note 2) For earth ring attachments, see CODE SYMBOLS.
Note 3) Flange type only
Conveter (Model: FMH)
Housing case
Flange Note 3)
Case of terminal box
• Material :
• Wiring connection port :
• Finish color :
• Protection class :
• Grounding :
• Mounting method :
• Input/output signal :
• Pulse output :
• Span setting :
• Flow direction change :
• Flow display :
• Total display :
Ambient temperature – fluid temperature allowable range
Signal electrode
Earth electrode
Earth ring Note 2)
consideration of erosion due to measuring fluid. Re-
fer to the table of material selection on the attached
sheet.
130
-25
50
[˚C]
0
-20
Ambient tempertaure
Lining
–25 to +130˚C (PFA, TFE lining)
G
Silver, Lid ....Beige
IP67
D-class grounding (100 or less)
Mounting on the pipe or wall
Current output; 4 to 20mA DC
Load rasistance 0 to 600
Pulse output; open-collector
Status output; open-collector
Status input; voltage input
Capacity: 16 to 30V DC
Internal resistance: 2k
Total pulses are outputted by setting total
constant. Pulse width 0.1 to 2000ms is
settable.
Flow rate full scale(FS) can be set by set-
ting flow rate unit and flow rate value.
Display cubic volume; m
Display time unit ; /d, /h, /min, /s
Flow direction can be reversed in flow di-
rection mode.
Real unit flow display, % display or user
unit display is possible. Max 6 disits.
Totaled volume can be displayed by set-
ting the unit of cubic volume.
Displayed cubic volume unit ; m
Totaled value is held when power failure
occurs.
1 /2
Capacity; 16 to 30V DC, 0.22A or less
ON voltage; 2V or less
Max. 5kHz
Capacity: 16 to 30V DC, 0.22A or less
ON voltage; 2V or less
10
25
Hasteroy C-4 equivalent
Aluminum alloy
SUS316 equivalent
Aluminum alloy
60
Tefron(PFA, TFE)
3
, L, mL
[˚C]
3
, L, mL
Other specifications
For different materials of the electrode and earth-ring, con-
tact with Fuji Electric.
Standard performance
• Fault diagnosis function :
• Zero point adjustment :
• Low cut :
• 0% signal lock :
• Filter :
• Empty detection :
• Flow switch :
• Dumping time constant :
• Density setting :
• Converter case :
• Wiring connection port :
• Finish color :
• Protection class :
• Grounding :
• Mass :
• Length of exclusive signal cable :
• Accuracy rating of display and pulse output :
• Accuracy rating of analog output :
• Power consumption :
• Operating condition :
Qv : Measuring flow velocity
Qv : Measuring flow velocity
0.7m/s or more
0.7m/s or more
0.7m/s 0or less
0.7m/s 0or less
Flow velocity
Flow velocity
Various faults can be diagnosed by hard-
ware check and process check.
Zero point is automatically calibrated with
key operation.
0 to 10% FS settable
Momentary output can be cut to 0% at
flow rate below the set cutoff point.
Note) Output low cut and total low cut are
Display and output can be locked to 0%
with status input.
A digital filter is included in the converter
especially for pulsating or noisy flow sig-
nals.
Absence of liquid is detected and status
signal is outputted only when diameter is
more than 10A and conductivity is more
than 20 S/cm.
0 to 130% FS
Status signal is outputted by setting high/
low limit flow.
1 to 99.999 sec
Available from 0.01 to 5.00g/cm
weight of the fluid can also be indicated.
Aluminum alloy
G
Silver, Lid ....Beige
IP67
D-class grounding (100 or less)
4.5kg
50m or less
14VA or less
Ambient temperature;
–25 to 60˚C (Detector : PFA, TFE lining)
–20 to 60˚C (Converter)
Ambient humidity; 95% RH or less (Note)
Power voltage; 100 to 230V AC +10%,
Power frequency; 50/60Hz
(Note)
If ambient humidity exceeds 95% RH, se-
lect a submersible type in FMB model.
1 /2
(with water-proof gland)
set at the same value.
0.0035
0.0035
Qv
Qv
0.5% of rate
Accuracy
0.6% of rate
Accuracy
100+0.1 % of rate
100 % of rate
-15%
3
, and the