W6691CD WINBOND [Winbond], W6691CD Datasheet - Page 66
W6691CD
Manufacturer Part Number
W6691CD
Description
ISDN S/T Interface Transceiver
Manufacturer
WINBOND [Winbond]
Datasheet
1.W6691CD.pdf
(106 pages)
- Current page: 66 of 106
- Download datasheet (466Kb)
abort the data and issue a RRST command to reset the receiver if RDOV = 1. The frame overflow condition
will not set this bit.
CRCE
RMB
RRST command to reset the receiver.
Note: Normally D_RSTA register should be read by the microprocessor after a D_RME interrupt. The contents
of D_RSTA are valid only after a D_RME interrupt and remain valid until the frame is acknowledged via a
RACK bit.
8.7.11 D_ch SAPI Address Mask
Value after reset: 00H
the corresponding bit comparisons with D_SAP1, D_SAP2 are disabled. Comparison with SAPG is always
performed.
controller will compare these two bytes with contents of D_SAPI1, DSAP2 and D_TEI1, D_TEI2. If the HDLC
frame SAPI matches D_SAPI1 or D_SAP2 and the HDLC frame TEI matches D_TEI1 or D_TEI2, the HDLC
frame is captured and stored in D_channel receiving FIFO. If comparison operation is enabled ( This means
that the more than one bit in D_SAM is set to “1”), except the frame with matching address is stored, others
are discarded. . If comparison operation is disabled ( This means that the all bits in D_SAM are set to “0”), all
frame with any address combination are captured and stored in receiving FIFO. The mask operation can be
programmed by each bit respectively. The HDLC frame with SAPG and /or TEIG address are always
captured and stored.
SAM7
This bit indicates the result of frame CRC check:
A "1" means that a sequence of seven 1's was received and the frame is aborted. Software must issue
This register masks(disables) the first byte address comparison of the incoming frame. If the mask bit is "1"
Each HDLC frame has two address byte. The first byte is SPAI and second byte is TEI. The D_ch HDLC
7
0: CRC correct
1: CRC error
Receive Message Aborted
CRC Error
SAM6
6
SAM5
5
SAM4
4
SAM3
D_SAM
3
SAM2
2
66
SAM1
1
Read/Write
SAM0
0
Preliminary W6691
Publication Release Date: Sep 2001
Address 0EH
Revision 1.1
Related parts for W6691CD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Isdn S/t Interface Transceiver
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
WINBOND I/O, UART, infrared, parallel port, game port, MIDI port, flash ROM interface, general purpose I/O ports, FDC, hardware monitor functions
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
Tone/pulse dialer with redial function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
SERIAL VOICE SRAM (128K · 1 BIT)
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
WE9142ATone/Pulse Telephone Dialer
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13 Memory Tone / Pulse Switchable Dialer with Save Function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
14-memory tone/pulse switchable dialer with handfree and lock functions
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
10-memory tone/pulse dialer with save function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
23-flash memory tone/pulse dialer with handfree, lock and hold functions
Manufacturer:
Winbond
Datasheet: