HFDOM44KR016 HANBIT [Hanbit Electronics Co.,Ltd], HFDOM44KR016 Datasheet

Page 1

HANBit 40Pin Flash Disk Module Min.8MB ~ Max.1GB, True IDE Interface Mode, 3.3V / 5.0V Operating 1. PRODUCT OVERVIEW GENERAL DESCRIPTION The HFDOM44KRxxx series 44Pin Flash Disk Module is a flash technology based with True IDE interface flash memory card. ...

Page 2

HANBit Operating Voltage : 3.3V / 5.0V Power consumption : 3.3V ± 5% Read mode <30 mA Write mode <56 mA Stop mode <2 mA Environment conditions : Operating temperature Storage temperature Relative humidity ELECTRICAL SPECIFICATIONS Table 1.1 Absolute Maximum ...

Page 3

... HANBit CAPACITY SPECIFICATIONS Table 1.4 Capacity Specifications Part Number Capacity (formatted) HFDOM44KR016 HFDOM44KR032 30,65 Mbytes HFDOM44KR064 61,32 Mbytes HFDOM44KR096 91,98 Mbytes 122,64 Mbytes HFDOM44KR128 119,65 Mbytes HFDOM44KR192 183,96 Mbytes 245,28 Mbytes HFDOM44KR256 239,29 Mbytes 369,91 Mbytes HFDOM44KR384 357,86 Mbytes 490,28 Mbytes HFDOM44KR512 478,59 Mbytes HFDOM44KR01G 981,00 Mbytes URL:www ...

Page 4

HANBit PHYSYCAL SPECIFICATION Jumper Master 1,2 Close URL:www.hbe.co.kr Rev. 1.0 (December, 2004) Slave 2,3 Close 2.7±0.1∅ 48.4±0.1mm 52.3±0.3mm < View from connector side > < View from Right side > HFDOM44KRxxx Jumper 31.0±0.5mm ...

Page 5

HANBit INSTALLTION GUIDE 1) Setting Method ① Make sure your computer is turned off before you open the case. ② Plug the carefully into the 40pin IDE slot on your computer. Caution: Make sure to align pin1 on host adapter ...

Page 6

HANBit 2. PIN INFORMATION PIN ASSIGNMENTS AND PIN TYPE Table 2.1 Pin Assignment and Pin type Pin Signal 1 /RESET 3 D07 5 D06 7 D05 9 D04 11 D03 13 D02 15 D01 17 D00 19 GND 21 INPACK ...

Page 7

HANBit Signal Descriptions Table 2.2 Signal Descriptions Signal Name Dir. Pin A[2:0] I 33,35,36 -PDIAG I/O 34 -DASP I/O 39 -CS0, -CS1 I 37,38 3,4,5,6, 7,8,9,10, D[15:00] I/O 11,12,13, 14,15,16, 17,18 2,19,22, GND -- 24,26, 30,40, -IOR I 25 -IOW ...

Page 8

HANBit BLOCK DIAGRAM PCMCIA ATA Interface HOST ATA Interface Interface RAM 3. INTERFACE BUS TIMING ACCESS SPCIFICATIONS 1 System clock timing Sym. Description Tc Clock cycle time Tlpd Clock low pulse duration Thpd Clock high pulse duration URL:www.hbe.co.kr Rev. 1.0 ...

Page 9

HANBit 2 Host Read/Write timing Sym bus asserted from HIOR# / HOE hold time after HIOR# / HOE# ( set up time of HIOW# / HWE# ( hold time of HIOW# / ...

Page 10

HANBit DATA Register Word Data Register Even Data Register Odd Data Register Odd Data Register Error/Feature Register Error/Feature Register Error/Feature Register 2) Error Register (Address – 1F1h[171h];Offset 1,0Dh Read Only) This register contains additional information about the source of an ...

Page 11

HANBit for any CompactFlash Storage Card data access for the subsequent command Cylinder Low (LBA 15-8 )Register (Address–1F4h[174h];Offset 4) This register contains the low order 8 bits of the starting cylinder address or bits 15-8 ...

Page 12

HANBit accept a command. Bit 5 (DWF): This bit, if set, indicates a write fault has occurred. Bit 4 (DSC): This bit is set when the CompactFlash Storage Card is ready. Bit 3 (DRQ): The Data Request is set when ...

Page 13

HANBit accomplished by either a) If possible, program the host adapter to enable only I/O addresses 1F0h-1F7h, 3F6h (or 170h-177h, 176h) to the CompactFlash Storage Card provided use an additional Primary / Secondary configuration in the CompactFlash ...

Page 14

HANBit 3 Write Multiple 3 WriteMultiple w/o Erase 2 Write Sector(s) 2 Write Sector(s) w/o Erase 38h 3 Write Verify Definitions: --FR = Features Register --SC = Sector Count Register --SN = Sector Number Register --CY = Cylinder Registers --DH ...

Page 15

HANBit If in PCMCIA configuration this command runs only on the CompactFlash Storage Card which is addressed by the Drive/Head register when the diagnostic command is issued. This is because PCMCIA card interface does not allows for direct inter-drive communication ...

Page 16

HANBit This command writes the desired head and cylinder of the selected drive with a vendor unique data pattern (typically FFh or 00h). To remain host backward compatible, the CompactFlash Storage Card expects a sector buffer of data from the ...

Page 17

HANBit 49 xx00h 2 50 0000h 2 51 0x00h 2 52 0000h 2 53 0001h 2 54 Xxxxh 2 55 xxxxh 2 56 xxxxh 2 57-58 xxxxh 4 59 010xh 2 60-61 xxxxh 4 62-127 0000h 138 128 xxxxh 2 ...

Page 18

HANBit Sec Cnt(2) Feature(1) This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. Initialize Drive Parameters – 91h Bit-> 7 Command(7) C/D/H(6) X Cyl High(5) Cyl Low(4) Sec Num(3) ...

Page 19

HANBit Sec Cnt(2) Feature(1) The Read Multiple command performs similarly to the Read Sectors command. Interrupts are not generated on every sector, but on the transfer of a block which contains the number of sectors defined by a Set Multiple ...

Page 20

HANBit Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command reads from 1 to 256 sectors as specified in the Sector Count register. A sector count of 0 requests 256 sectors. The transfer ...

Page 21

HANBit Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command is effectively a NOP command to the CompactFlash Storage Card and is provided for compatibility purposes. Request Sense – 03h Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec ...

Page 22

HANBit 03h 22h Seek –7X h Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command is effectively a NOP command to the CompactFlash Storage Card although it does perform a range check of ...

Page 23

HANBit 97h Accepted for backward compatibility . Use of this Feature is not recommended 9Ah Set the host current source capability. Allows tradeoff between current drawn and read/write speed. BBh 4 bytes of data apply on Read/Write Long commands CCh ...

Page 24

HANBit Bit-> 7 Command(7) C/D/H(6) X Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command causes the CompactFlash Storage Card to set BSY, enter the Sleep mode, clear BSY and generate an interrupt. Recovery from sleep mode is ...

Page 25

HANBit This command causes the CompactFlash Storage Card to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately. Recovery from sleep mode is accomplished by simply issuing another command ...

Page 26

HANBit Feature(1) For the CompactFlash Storage Cards that do not support security mode feature set, this command is effectively a NOP command and only implemented for backward compatibility. The Sector Count Register will always be returned with a 00h indicating ...

Page 27

HANBit Bit-> 7 Command(7) C/D/H(6) X Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) Note: The current revision of the CompactFlash Storage Card only supports a block count indicated in the Identify Drive Command information. This ...

Page 28

HANBit Write Sector(s) – 30h or 31h Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command writes from 1 to 256 sectors as specified in the Sector Count Register. A sector count of ...

Page 29

HANBit Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command is similar to the Write Sector(s) command, except each sector is verified immediately after being written. This command has the same protocol as ...

Page 30

HANBit Write Buffer Write Long Sector Write Multiple Write Multiple w/o Erase Write Sector(s) Write Sector(s) w/o Erase Write Verify Sector(s) Invalid Command Code V = Valid on this command Ordering Infomation NO 1 DOM44KR016 2 DOM44KR032 3 DOM44KR096 4 ...