EPC110 EPC [Espros Photonics corp], EPC110 Datasheet - Page 2

• Manufacturer Part Number: EPC110
• Description: Fully integrated configurable light barrier driver & receiver
• Manufacturer: EPC [Espros Photonics corp]

Absolute Maximum Ratings
Voltage at any pin except pin VDD
Power Supply Voltage at pin VDD
Programming Voltage at pin VDD
Power Supply Voltage at pin VDD33
Output current at any pin except pin LED
Power Consumption with maximum load
Lead Temperature solder, 4 sec. (T
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended operating conditions
indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specific -
ations and test conditions, see Electrical Characteristics.
Note 2: This device is a highly sensitive CMOS ac current amplifier with an ESD rating of JEDEC HBM class 0 (<250V). Handling and
assembly of this device should only be done at ESD protected workstations.
Electrical Characteristics
3.0V < V
General Data
© 2011 ESPROS Photonics Corporation
Characteristics subject to change without notice
Symbol
V
I
V
V
LEAKD
I
V
R
df
V
V
I
V
V
V
Prog
f
LEDH
LED
I
PUP
HOH
clk
PP
N
OH
OL
PU
IH
IL
clk
N
N
< 3.6V, -40°C < T
Operating power supply voltage
Power-up Threshold Voltage
Ripple on supply voltage,
peak to peak
Current consumption operating
Current consumption programming in program mode, VDD @ 8.0V, I
Output high voltage
Output low voltage
Output high voltage OUTH
Output high voltage LED
Source current maximum
Input high voltage
Input low voltage
Input leakage current
Pull-up resistor
Reference clock
Temperature drift
Parameter
A
< +85°C, unless otherwise specified
L
)
(Notes 1, 2)
-0.3V to V
-0.3V to +5.5V
-0.3V to +8.0V
-0.3V to +5.5V
-6mA to +6mA
125 mW
+260°C
at VDD33 (and VDD)
Voltage at VDD33 when the device starts up
in operation mode, I
except OUTH and LED
@ 4mA source, including OUTH and LED
see Figure 8
@ 0.1mA sink current
at Pin LED, V
internal at digital input
of internal oscillator - for information only
All internal timings are referenced to this clock
of the oscillator - for information only
Conditions/Comments
N
+0.3 V
LED
@ 0... V
PD
Recommended Operating Conditions
Operating supply voltage at VDD
Programming voltage at VDD
Operating supply voltage at VDD33
Operating Temperature (T
Humidity (non-condensing)
= 0 mA, no load
2
N
- 1.0V
Input pulse I
PD
= 0 mA, no load
108nA
36nA
48nA
72nA
PD NST
O
)
V
V
0.7*V
N
N
GND
Min.
2.4
0.7
- 0.5V
- 0.5V
30
3
N
Values
Min.
-40°
3.0
7.0
3.0
+5
Typ.
Datasheet epc110 - V2.1
640
32
0.3*V
Max.
+85°
Max.
+95
www.espros.ch
3.6
8.0
3.6
150
350
600
200
3.6
0.5
1.3
70
V
10
3
2
4
N
epc110
N
Units
ppm/K
Units
MHz
mV
mV
mV
mV
mA
mA
mA
%
V
V
V
C
µA
kΩ
V
V
V
V
V
V