SH3000UM SEMTECH [Semtech Corporation], SH3000UM Datasheet - Page 17

• Manufacturer Part Number: SH3000UM
• Manufacturer: SEMTECH [Semtech Corporation]

Low Frequency (LF) Oscillator System
This module provides the 32.768kHz clock to all internal
circuits and to the dedicated output pin, CLK32. If en-
abled, the CLK32 output continues normal operations
when VDD is absent and backup power is available.
When the power is fi rst applied to the SH3003, the RC
oscillator takes over. It supplies the 32.768 kHz clock for
start-up and initialization. However, if the CLKSEL pin is
set high, then the crystal oscillator is enabled. Once the
crystal has started and stabilized, the internal 32.768 Hz
clock switches to the very accurate crystal frequency; see
Figure 5.
Just like the VBO value for the Reset circuit, the default
calibration values for the RC oscillator are loaded on pow-
er-up from the factory-programmed non-volatile memo-
ry. They can be re-programmed at any time or they can
be permanently protected from any changes by setting
the Lock fl ag or a write-protect fl ag. Factory calibration
brings the frequency of the RC oscillator within ± % of the
32.768kHz for the internal reference resistor, and ±2% for
the external 1MΩ 1% resistor, over the entire temperature
and supply voltage range.
The frequency of the RC oscillator can be tuned or mod-
ulated by varying the external reference resistor, which
should be located as close as possible to RREF, pin 9.
©2006 Semtech Corp.
POWER MANAGEMENT
POWER MANAGEMENT
Application Information
1 M 1% or
12.5 pF Load
Capacitance
Reference
32.768 kHz
X-
External
Resistor
variable
Crystal
TAL
RC
V
REG
CLK
X
X
R
V
V
IN
OUT
REF
SEL
SS
SS
5
6
7
9
8
1
(continued)
Lock / Unlock
Logic
Figure 5. Simplified LF Oscillator System
4-bit Value
6-bit Value
17
I
R
NTERNAL
REF
The crystal oscillator has the useful feature of adjustable
load capacitors. It permits tuning of the circuit for initial
tolerance of the crystal (often ±20ppm) as well as an ad-
justment for the required load capacitance (with possible
variations from the PCB layout). While the oscillator was
designed for a crystal with a nominal load capacitance of
12.5pF, the circuit accommodates any value from ~7pF to
22pF (depending on parasitics of the layout). All of these
corrections can be performed when the part is already
installed on the PCB, in the actual circuit.
The default value for load capacitance (12.5pF) loaded on
power-up from the factory-programmed nonvolatile mem-
ory can be re-programmed at any time (following a secure
process of unlocking the load capacitance value register
and immediately writing a new setting), or it can be com-
pletely protected from any changes by a permanent write-
protect fl ag. This adjustment can set the frequency of the
crystal oscillator to within ±4ppm of the ideal value. As
a reference, a typical 32.768kHz crystal changes its fre-
quency 4ppm for a 10°C change in temperature.
Since the temperature characteristics of crystals are well
known and stable, the host processor is free to implement
an algorithm for temperature compensation of the crystal
oscillator using the adjustable load capacitors, with re-
sulting accuracy of ±4ppm over the entire temperature
range.
O
N
4-bit Value
Oscillator
X-tal stable?
RC
Internal R
Lock Logic
REF
kHz Clock
CLK32 O
Internal
32.768
From / To
Serial I/O
N
www.semtech.com
CLK32
13
SH3003