M27C64A-30F6X STMicroelectronics, M27C64A-30F6X Datasheet

no-image

M27C64A-30F6X

Manufacturer Part Number
M27C64A-30F6X
Description
64 Kbit 8Kb x 8 UV EPROM and OTP EPROM
Manufacturer
STMicroelectronics
Datasheet
DESCRIPTION
The M27C800 is an 8 Mbit EPROM offered in the
two ranges UV (ultra violet erase) and OTP (one
time programmable). It is ideally suited for micro-
processor systems requiring large data or program
storage. It is organised as either 1 Mwords of 8 bit
or 512 Kwords of 16 bit. The pin-out is compatible
with the most common 8 Mbit Mask ROM.
The FDIP42W (window ceramic frit-seal package)
has a transparent lid which allows the user to ex-
pose the chip to ultraviolet light to erase the bit pat-
tern.
A new pattern can then be written rapidly to the de-
vice by following the programming procedure.
For applications where the content is programmed
only one time and erasure is not required, the
M27C800 is offered in PDIP42, PLCC44 and
SO44 packages.
January 2000
5V
OPERATION
ACCESS TIME: 50ns
BYTE-WIDE or WORD-WIDE
CONFIGURABLE
8 Mbit MASK ROM REPLACEMENT
LOW POWER CONSUMPTION
– Active Current 70mA at 8MHz
– Stand-by Current 50 A
PROGRAMMING VOLTAGE: 12.5V
PROGRAMMING TIME: 50 s/word
ELECTRONIC SIGNATURE
– Manufacturer Code: 20h
– Device Code: B2h
8 Mbit (1Mb x8 or 512Kb x16) UV EPROM and OTP EPROM
10% SUPPLY VOLTAGE in READ
0.25V
Figure 1. Logic Diagram
42
BYTEV PP
A0-A18
FDIP42W (F)
1
PLCC44 (K)
G
E
19
V CC
V SS
M27C800
42
44
M27C800
1
PDIP42 (B)
SO44 (M)
1
15
Q15A–1
Q0-Q14
AI01593
1/17

Related parts for M27C64A-30F6X

M27C64A-30F6X Summary of contents

Page 1

Mbit (1Mb x8 or 512Kb x16) UV EPROM and OTP EPROM 5V 10% SUPPLY VOLTAGE in READ OPERATION ACCESS TIME: 50ns BYTE-WIDE or WORD-WIDE CONFIGURABLE 8 Mbit MASK ROM REPLACEMENT LOW POWER CONSUMPTION – Active Current 70mA at 8MHz ...

Page 2

M27C800 Figure 2A. DIP Connections A18 A17 A10 A11 A12 A13 A14 ...

Page 3

... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi- tions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant qual- ity documents. ...

Page 4

... When the BYTEV pin the Byte-wide or ganisation is selected and the Q15A–1 pin is used for the Address Input A–1. When the memory is logically regarded as 16 bit wide, but read in the Byte-wide organisation, then with A– 4/17 High Speed 10ns ...

Page 5

Table 6. Capacitance ( MHz) A Symbol Parameter Input Capacitance (except BYTEV C IN Input Capacitance (BYTEV C Output Capacitance OUT Note: 1. Sampled only, not 100% tested. Table 7. Read Mode DC ...

Page 6

M27C800 Table 8A. Read Mode AC Characteristics ( – Symbol Alt Parameter Address Valid to Output t t AVQV ACC Valid BYTE High to Output t t BHQV ...

Page 7

... READ line from the system control bus. This ensures that all deselect- ed memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device ...

Page 8

M27C800 Figure 6. Byte-Wide Read Mode AC Waveforms A–1,A0-A18 E G Q0-Q7 Note: BYTEV = V PP IL. Figure 7. BYTE Transition AC Waveforms A0-A18 A–1 tAVQV BYTEV PP Q0-Q7 tBLQX Q8-Q15 tBLQZ Note: Chip Enable (E) and Output Enable ...

Page 9

Table 9. Programming Mode DC Characteristics ( 6.25V 0.25V Symbol Parameter I Input Leakage Current LI I Supply Current CC I Program Current PP V Input Low Voltage IL V Input High ...

Page 10

M27C800 Figure 8. Programming and Verify Modes AC Waveforms A0-A18 Q0-Q15 BYTEV PP tVPHAV V CC tVCHAV E G Figure 9. Programming Flowchart 6.25V 12. Pulse NO ...

Page 11

... IL code and byte 1 ( the device identifier IH code. For the STMicroelectronics M27C800, these two identifier bytes are given in Table 4 and can be read-out on outputs Q7 to Q0. ERASURE OPERATION (applies to UV EPROM) The erasure characteristics of the M27C800 is such that erasure begins when the cells are ex- posed to light with wavelengths shorter than ap- proximately 4000 Å ...

Page 12

... TR = Tape & Reel Packing Note: 1. High Speed, see AC Characteristics section for further information. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de- vice, please contact the STMicroelectronics Sales Office nearest to you. Table 1. Revision History Date March 1999 ...

Page 13

Table 12. FDIP42W - 42 pin Ceramic Frit-seal DIP, with window, Package Mechanical Data Symb Typ 1. 54.41 D2 50.80 E 15.24 E1 14.50 e 2.54 eA 14.99 eB 16. ...

Page 14

M27C800 Table 13. PDIP42 - 42 pin Plastic DIP, 600 mils width, Package Mechanical Data Symb Typ 52.20 D2 50.80 E 15.24 E1 13.59 e1 2.54 eA 14.99 eB 15. ...

Page 15

Table 14. PLCC44 - 44 lead Plastic Leaded Chip Carrier, Package Mechanical Data Symb Typ 17.40 D1 16.51 D2 14.99 E 17.40 E1 16.51 E2 14. Figure ...

Page 16

M27C800 Table 15. SO44 - 44 lead Plastic Small Outline, 525 mils body width, Package Mechanical Data Symb Typ 28.10 E 13.20 e 1.27 H 15. Figure 13. SO44 ...

Page 17

... No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in lif e support devices or systems without express written approval of STMicroelectronics ...

Related keywords