LP2975AIMM-12 National Semiconductor, LP2975AIMM-12 Datasheet - Page 12

• Manufacturer Part Number: LP2975AIMM-12
• Description: MOSFET LDO Driver/Controller
• Manufacturer: National Semiconductor

www.national.com
Application Hints
For maximum accuracy, the INPUT and CURRENT LIMIT
pins must be Kelvin connected to R
caused by voltage drops along the traces carrying the cur-
rent from the input supply to the Source pin of the FET.
EXTERNAL CAPACITORS
The best capacitors for use in a specific design will depend
on voltage and load current (examples of tested circuits for
several different output voltages and currents are provided in
a previous section.)
Information in the next sections is provided to aid the de-
signer in the selection of the external capacitors.
INPUT CAPACITOR: Although not always required, an input
capacitor is recommended. Good bypassing on the input as-
sures that the regulator is working from a source with a low
impedance, which improves stability. A good input capacitor
can also improve transient response by providing a reservoir
of stored energy that the regulator can utilize in cases where
the load current demand suddenly increases. The value
used for C
erence Designs section for examples of input capacitors.
OUTPUT CAPACITOR: The output capacitor is required for
loop stability (compensation) as well as transient response.
During sudden changes in load current demand, the output
capacitor must source or sink current during the time it takes
the control loop of the LP2975 to adjust the gate drive to the
pass FET. As a general rule, a larger output capacitor will im-
prove both transient response and phase margin (stability).
The value of C
OUTPUT CAPACITOR AND COMPENSATION: Loop com-
pensation for the LP2975 is derived from C
cases, the feed-forward capacitor C
C
load resistance which causes the loop gain to roll off (de-
crease) at an additional −20 dB/decade. The frequency of
the pole is:
Where:
R
C
ESR is the equivalent series resistance of C
As a general guideline, the frequency of f
Hz. It should be noted that higher load currents correspond
to lower values of R
to keep f
DESIGN EXAMPLE: Select the minimum required output
capacitance for a design whose output specifications are 5V
@
Re-written:
Values used for the calculation:
f
Solving for C
would be 180 µF).
The ESR of the output capacitor is very important for stabil-
ity, as it creates a zero (f
shift resulting from one of the poles present in the loop. The
frequency of the zero is calculated from:
p
OUT
L
OUT
= 200 Hz, R
1A:
is the load resistance.
forms a pole (referred to as f
is the value of the output capacitor.
p
IN
at a given frequency.
may be increased without limit. Refer to the Ref-
f
f
C
OUT
p
p
L
OUT
OUT
= 0.16 / [ (R
= 0.16 / [ (R
= 5 , ESR = 0.1
f
, we get 157 µF (nearest standard size
z
may be increased without limit.
L
= 0.16 / [f
= 0.16 / (ESR x C
, which requires that C
z
) which cancels much of the phase
L
L
p
+ ESR) x C
+ ESR) x C
(Continued)
x (R
L
p
(assumed).
F
) in conjuction with the
+ ESR) ]
(see next section).
OUT
SC
p
)
OUT
OUT
, to avoid errors
OUT
OUT
should be
]
]
and, in some
OUT
be increased
.
200
12
For best results in most designs, the frequency of f
fall between 5 kHz and 50 kHz. It must be noted that the val-
ues of C
verely in the case of aluminum electrolytics), and this must
be taken into consideration.
For the design example (V
which meets the f
ESR yields:
Assuming f
for the 180 µF capacitor are found to be:
A good-quality, low-ESR capacitor type such as the Pana-
sonic HFQ is a good choice. However, the 10V/180 µF ca-
pacitor (#ECA-1AFQ181) has an ESR of 0.3 which is not in
the desired range.
To assure a stable design, some of the options are:
1) Use a different type capacitor which has a lower ESR
such as an organic-electrolyte OSCON.
2) Use a higher voltage capacitor. Since ESR is inversely
proportional to the physical size of the capacitor, a higher
voltage capacitor with the same C value will typically have a
lower ESR (because of the larger case size). In this ex-
ample, a Panasonic ECA-1EFQ181 (which is a 180 µF/25V
part) has an ESR of 0.17 and would meet the desired ESR
range.
3) Use a feed-forward capacitor (see next section).
FEED-FORWARD CAPACITOR: Although not required in
every application, the use of a feed-forward capacitor (C
can yield improvements in both phase margin and transient
response in most designs.
The added phase margin provided by C
lations in cases where the required value of C
can not be easily obtained (see previous section).
C
from the Gate capacitance, stabilizing applications where
this pole occurs at a low frequency (before cross-over) which
would cause oscillations if left uncompensated (see later
section GATE CAPACITANCE POLE FREQUENCY).
Even in a stable design, adding C
optimal loop response (faster settling time). For these rea-
sons, the use of a feed-forward capacitor is always rec-
ommended.
C
set the output voltage (see Typical Application Circuit). This
forms a zero in the loop response (defined as f
quency is:
When solved for C
For most applications, f
50 kHz.
ADJUSTING THE OUTPUT VOLTAGE
If an output voltage is required which is not available as a
standard voltage, the LP2975 can be used as an adjustable
regulator (see Typical Application circuit). The external resis-
tors R1 and R2 (along with the internal 24 k
the output voltage.
It is important to note that R2 is connected in parallel with the
internal 24 k
tance between the COMP pin and ground, then its value
will be the parallel combination of R2 and 24 k :
F
F
is connected across the top resistor in the divider used to
can also reduce the phase shift due to the pole resulting
f
C
OUT
zf
F
z
= 6.6 x 10
= 6.6 x 10
= 5 kHz and 50 kHz, the limiting values of ESR
and ESR usually vary with temperature (se-
resistor. If we define R
ESR = 0.16 / (f
18 m
z
F
, the f
requirements. Solving the equation for
−6
−6
zf
/ [C
/ [f
zf
should be set between 5 kHz and
OUT
ESR
equation is:
zf
F
= 5V
x (V
x (V
z
F
x C
OUT
OUT
will typically provide more
0.18
@
EQ
1A), select a capacitor
OUT
/ 1.24 − 1) ]
/ 1.24 − 1) ]
F
as the total resis-
)
can prevent oscil-
zf
OUT
), whose fre-
resistor) set
and ESR
z
should
F
)