DP83848YB_08 NSC [National Semiconductor], DP83848YB_08 Datasheet - Page 34
DP83848YB_08
Manufacturer Part Number
DP83848YB_08
Description
Manufacturer
NSC [National Semiconductor]
Datasheet
1.DP83848YB_08.pdf
(84 pages)
- Current page: 34 of 84
- Download datasheet (4Mb)
www.national.com
5.2 ESD Protection
Typically, ESD precautions are predominantly in effect
when handling the devices or board before being installed
in a system. In those cases, strict handling procedures
need be implemented during the manufacturing process to
greatly reduce the occurrences of catastrophic ESD
events. After the system is assembled, internal compo-
nents are less sensitive from ESD events.
See Section 8.0 for ESD rating.
5.3 Clock In (X1) Requirements
The DP83848YB supports an external CMOS level oscilla-
tor source or a crystal resonator device.
Oscillator
If an external clock source is used, X1 should be tied to the
clock source and X2 should be left floating.
Specifications for CMOS oscillators: 25 MHz in MII Mode
and 50 MHz in RMII Mode are listed in Table 7 and Table 8.
Crystal
A 25 MHz, parallel, 20 pF load crystal resonator should be
used if a crystal source is desired. Figure 12 shows a typi-
cal connection for a crystal resonator circuit. The load
1
This limit is provided as a guideline for component selection and to guaranteed by production testing.
Refer to AN-1548, “PHYTER 100 Base-TX Reference Clock Jitter Tolerance,“ for details on jitter performance.
Rise / Fall Time
Parameter
Frequency
Frequency
Frequency
Symmetry
Tolerance
Stability
Jitter
Jitter
40%
Min
Table 7. 25 MHz Oscillator Specification
Typ
25
800
800
34
Max
60%
+50
+50
6
capacitor values will vary with the crystal vendors; check
with the vendor for the recommended loads.
The oscillator circuit is designed to drive a parallel reso-
nance AT cut crystal with a minimum drive level of 100 W
and a maximum of 500 W. If a crystal is specified for a
lower drive level, a current limiting resistor should be
placed in series between X2 and the crystal.
As a starting point for evaluating an oscillator circuit, if the
requirements for the crystal are not known, C
should be set at 33 pF, and R
Specification for 25 MHz crystal are listed in Table 9.
1
1
Figure 12. Crystal Oscillator Circuit
C
L1
Units
MHz
nsec
psec
psec
ppm
ppm
X1
1
should be set at 0
Temperature
1 year aging
Operational
20% - 80%
Duty Cycle
Condition
Short term
Long term
X2
R
C
1
L2
L1
and C
L2
Related parts for DP83848YB_08
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Thin SOT23 1A Load Step-Down DC-DC Regulator
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
TRI-STATE Dual Receiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Hex MOS Drivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Quad High Current Peripheral Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
(RS-422/RS-423) Line Drivers with TRI-STATE Outputs
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Multipoint RS485/RS422 Transceivers/Repeaters
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Low Power EIA-RS-485 Transceiver with Sleep Mode
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
BTL Handshake Transceiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Octal 80-Bit Static Shift Register
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
PUSH BUTTON PULSE DIALER CIRCUITS
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Hex Schmitt Trigger with Extended Input Voltage
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Microprocessor Real Time Clock
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Dual Line Receivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Dual TRI-STATE Differential Line Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet: