PIC17C756A MICROCHIP [Microchip Technology], PIC17C756A Datasheet - Page 139

no-image

PIC17C756A

Manufacturer Part Number
PIC17C756A
Description
High-Performance 8-bit CMOS EPROM Microcontrollers with 10-bit A/D
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC17C756A
Manufacturer:
Microchip
Quantity:
6
Part Number:
PIC17C756A-16/L
Manufacturer:
MICROCHIP
Quantity:
101
Part Number:
PIC17C756A-16/L
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC17C756A-16/L
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC17C756A-16/PT
Manufacturer:
SA
Quantity:
12 000
Part Number:
PIC17C756A-16/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC17C756A-16/PT
Manufacturer:
MICROCHI
Quantity:
20 000
Part Number:
PIC17C756A-16E/L
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC17C756A-16E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC17C756A-16I/L
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC17C756A-16I/L
Manufacturer:
MICROCH
Quantity:
20 000
Part Number:
PIC17C756A-16I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC17C756A-16I/PT
0
Part Number:
PIC17C756A-33
Manufacturer:
Microchip
Quantity:
5 510
Part Number:
PIC17C756A-33
Manufacturer:
INTEL
Quantity:
5 510
Part Number:
PIC17C756A-33/L
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
15.1.4
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2, Figure 15-5) is to broad-
cast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
The clock polarity is selected by appropriately program-
ming bit CKP (SSPCON1<4>). This then, would give
waveforms for SPI communication as shown in
FIGURE 15-6:
2000 Microchip Technology Inc.
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
SDO
(CKE = 1)
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
Input
Sample
(SMP = 1)
SSPIF
SSPSR to
SSPBUF
MASTER MODE
SPI MODE WAVEFORM (MASTER MODE)
bit7
bit7
bit7
bit7
bit6
bit6
bit5
bit5
bit4
bit4
Figure 15-6, Figure 15-8 and Figure 15-9, where the
MSb is transmitted first. In Master mode, the SPI clock
rate (bit rate) is user programmable to be one of the
following:
• F
• F
• F
• Timer2 output/2
This allows a maximum bit clock frequency (at 33 MHz)
of 8.25 MHz.
Figure 15-6 shows the waveforms for Master mode.
When CKE = 1, the SDO data is valid before there is a
clock edge on SCK. The change of the input sample is
shown based on the state of the SMP bit. The time
when the SSPBUF is loaded with the received data is
shown.
bit3
bit3
OSC
OSC
OSC
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
bit2
bit2
CY
)
bit1
bit1
CY
CY
)
)
PIC17C7XX
bit0
bit0
bit0
bit0
DS30289B-page 139
Next Q4 cycle
after Q2
4 clock
modes

Related parts for PIC17C756A