XE8806A SEMTECH [Semtech Corporation], XE8806A Datasheet - Page 92
![no-image](/images/no-image-200.jpg)
XE8806A
Manufacturer Part Number
XE8806A
Description
Ultra Low-Power Low-Voltage
Manufacturer
SEMTECH [Semtech Corporation]
Datasheet
1.XE8806A.pdf
(143 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XE8806AMI026TLF
Manufacturer:
MAXIM
Quantity:
230
- Current page: 92 of 143
- Download datasheet (895Kb)
If RfifEnCod in register RegRfifCmd2 is set to 1, the bit stream coming from the shift register is encoded first
before sending it to the RFIF3 pin. The type of protocol is selected using the RfifPCM[2:0] control word in the
register RegRfifCmd2. The selection control bits are given in Table 14-14.
PCM Codes
When the bit RfifEnCod is modified while a transmission is active, the modification will take effect only when a new
byte is loaded from the FIFO into the shift register.
While the encoder is enabled, it is not possible to send a protocol violation as a start pattern. If a protocol violation
is used as a start sequence in the Manchester or Miller protocol, the following sequence should be used:
Beware that in the case a protocol violation is used as a start sequence in Manchester-level or Miller coding, the
used violation will depend on the value of the first bit of the message. As an example: if the Manchester level
coding is used and the first bit of the message is a 0 (encoded 01), the start sequence needs to be a series of 1’s.
If a series of 0’s would be used, the receiver would be unable to distinguish the leading 0 of the message from the
start sequence.
When the encoder is bypassed (RfifEnCod = 0), bits RfifPCM[2:0] still have an influence on the output bit stream :
when the NRZ coding is chosen, the bits are shifted out at the selected bit rate. If the Manchester or Miller codes
are selected however, the bits are shifted out at twice the data rate. This allows the use of two bits in the FIFO to
encode the bits by software.
14.9.4
If required, a bit synchronization clock can be generated on the pin RFIF2 if the data is uncoded or if the NRZ
coding is used (bits RfifEnCod and RfifPCM[2:0] in RegRfifCmd2). To generate this clock, the bit RfifTxClock in
RegRfifCmd2 has to be set. The timing of the generated clock is shown in Figure 14-7.
© Semtech 2006
RfifPCM[2:0]
1) wait until the transmission FIFO is empty (which means the last byte of the preceding message is being
2) clear RfifEnCod,
3) write the uncoded start pattern to the transmission FIFO
4) wait until the transmission FIFO is empty (which means the last byte of the uncoded start pattern is being
5) set RfifEnCod
6) write the message bytes to the FIFO
7) back to 1.
coded and sent),
sent)
Transmission synchronization clock
Level
000
Mark
NRZ
001
Table 14-16: PCM code selection
Space
010
14-12
Level
011
Bi-Phase/Manchester
Mark
100
Space
101
XE8806A/XE8807A
Miller
11X
www.semtech.com
Related parts for XE8806A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![6666](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1084CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1587CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
![ACS8515](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SR3.3](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
![SC1151CS](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1182CSW](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1185CSW](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1150CS](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1152CS](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![MMBT9012](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![MMBT9013](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![MMBT9014](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: