ADSP-21266_07 AD [Analog Devices], ADSP-21266_07 Datasheet - Page 13
![no-image](/images/no-image-200.jpg)
ADSP-21266_07
Manufacturer Part Number
ADSP-21266_07
Description
Embedded Processor
Manufacturer
AD [Analog Devices]
Datasheet
1.ADSP-21266_07.pdf
(44 pages)
Table 3. Pin Descriptions (Continued)
1
2
3
4
Pin
CLKIN
XTAL
CLK_CFG1–0
RESETOUT/CLKOUT O
RESET
TCK
TMS
TDI
TDO
TRST
EMU
V
V
A
A
GND
RD, WR, and ALE are continuously driven by the DSP and will not be three-stated.
Output only is a three-state driver with its output path always enabled.
Input only is a three-state driver, with both output path and pull-up disabled.
Three-state is a three-state driver, with pull-up disabled.
DDINT
DDEXT
VDD
VSS
Type
I
O
I
I/A
I
I/S
I/S
O
I/A
O (O/D)
P
P
P
G
G
State During and
After Reset
Input only
Output only
Input only
Output only
Input only
Input only
Three-state with
pull-up enabled
Three-state with
pull-up enabled
Three-state
Three-state with
pull-up enabled
Three-state with
pull-up enabled
3
4
2
Rev. C | Page 13 of 44 | October 2007
Function
Local Clock In. Used in conjunction with XTAL. CLKIN is the ADSP-21266 clock input.
It configures the ADSP-21266 to use either its internal clock generator or an external
clock source. Connecting the necessary components to CLKIN and XTAL enables the
internal clock generator. Connecting the external clock to CLKIN while leaving XTAL
unconnected configures the ADSP-21266 to use the external clock source such as
an external clock oscillator. The core is clocked either by the PLL output or this clock
input depending on the CLK_CFG1–0 pin settings. CLKIN should not be halted,
changed, or operated below the specified frequency.
Crystal Oscillator Terminal. Used in conjunction with CLKIN to drive an external
crystal.
Core/CLKIN Ratio Control. These pins set the start up clock frequency. See
for a description of the clock configuration modes.
Note that the operating frequency can be changed by programming the PLL multi-
plier and divider in the PMCTL register at any time after the core comes out of reset.
Reset Out/Local Clock Out. Drives out the core reset signal to an external device.
CLKOUT can also be configured as a reset out pin (RESETOUT). The functionality can
be switched between the PLL output clock and reset out by setting Bit 12 of the
PMCTL register. The default is reset out.
Processor Reset. Resets the ADSP-21266 to a known state. Upon deassertion, there
is a 4096 CLKIN cycle latency for the PLL to lock. After this time, the core begins
program execution from the hardware reset vector address. The RESET input must
be asserted (low) at power-up.
Test Clock (JTAG). Provides a clock for JTAG boundary scan. TCK must be asserted
(pulsed low) after power-up or held low for proper operation of the ADSP-21266.
Test Mode Select (JTAG). Used to control the test state machine. TMS has a
22.5 kΩ internal pull-up resistor.
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI has a
22.5 kΩ internal pull-up resistor.
Test Data Output (JTAG). Serial scan output of the boundary scan path.
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed
low) after power-up or held low for proper operation of the ADSP-21266. TRST has
a 22.5 kΩ internal pull-up resistor.
Emulation Status. Must be connected to the ADSP-21266 Analog Devices DSP
Tools product line of JTAG emulators target board connector only. EMU has a
22.5 kΩ internal pull-up resistor.
Core Power Supply. Nominally +1.2 V dc and supplies the DSP’s core processor
(13 pins on the BGA package, 32 pins on the LQFP package).
I/O Power Supply. Nominally +3.3 V dc (6 pins on the BGA package, 10 pins on the
LQFP package).
Analog Power Supply. Nominally +1.2 V dc and supplies the DSP’s internal PLL
(clock generator). This pin has the same specifications as V
filtering circuitry is required.
Analog Power Supply Return.
Power Supply Return. (54 pins on the BGA package, 39 pins on the LQFP package).
For more information, see Power Supplies on Page 8.
DDINT
ADSP-21266
, except that added
Table 6