MCP434X MICROCHIP [Microchip Technology], MCP434X Datasheet - Page 54
MCP434X
Manufacturer Part Number
MCP434X
Description
7/8-Bit Quad SPI Digital POT with Non-Volatile Memory
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.MCP434X.pdf
(80 pages)
- Current page: 54 of 80
- Download datasheet (3Mb)
MCP434X/436X
7.6
The Read command is a 16-bit command. The Read
Command can be issued to both the Volatile and
Non-Volatile memory locations. The format of the
command is shown in
The first 6 bits of the Read command determine the
address and the command. The 7th clock will output
the CMDERR bit on the SDO pin. The remaining
9-clocks the device will transmit the 9 data bits (D8:D0)
of the specified address (AD3:AD0).
Figure 7-4
Read command.
During a write cycle (Write or High Voltage Write to a
Non-Volatile memory location) the Read command can
only read the Volatile memory locations. By reading the
Status Register (04h), the Host Controller can
determine when the write cycle has completed (via the
state of the EEWA bit).
FIGURE 7-4:
DS22233A-page 54
SDI
SDO
D
A
3
1
1
Read Data
Normal and High Voltage
shows the SDI and SDO information for a
D
A
2
1
1
COMMAND BYTE
A
D
1
1
1
A
D
0
1
1
Figure
Read Command - SDI and SDO States.
1
1
1
1
1
1
7-4.
X
1
0
D
X
8
0
X
D
7
0
X
D
6
0
READ DATA
X
D
5
0
DATA BYTE
X
D
4
0
D
X
3
0
D
X
2
0
7.6.1
The read operation requires that the CS pin be in the
active state (V
the inactive state (V
(V
Byte and Data Byte) is then clocked in on the SCK and
SDI pins. The SDO pin starts driving data on the 7th bit
(CMDERR bit) and the addressed data comes out on
the 8th through 16th clocks.
Figure 6-3
X
D
1
0
IL
or V
X
D
0
0 Attempted Non-Volatile Memory Read
IHH
Valid Address/Command combination
during Non-Volatile Memory Write Cycle
show possible waveforms for a single read.
). The 16-bit Read Command (Command
SINGLE READ
IL
or V
IHH
IH
) and is driven to the active state
). Typically, the CS pin will be in
© 2009 Microchip Technology Inc.
Figure 6-2
through
Related parts for MCP434X
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
Low-Cost NV Digital POT with WiperLock™ Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
28/40/44-Pin Flash Microcontrollers with nanoWatt XLP Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
8-Pin Flash Microcontrollers with nanoWatt XLP Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
8/14-Pin, Flash-Based 8-Bit CMOS Microcontrollers with nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
500mA Fixed Output CMOS LDO with Shutdown
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
500mA Fixed Output, Fast Response CMOS LDO with Shutdown
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
1.5A Dual Open-Drain MOSFET Drivers
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
1.5A DUAL HIGH-SPEED POWER MOSFET DRIVERS
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
Single/Dual Digital Potentiometer with SPI™ Interface
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet: