MPC857DSL Motorola, MPC857DSL Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/4/459/motorola_sml.jpg)
MPC857DSL
Manufacturer Part Number
MPC857DSL
Description
(MPC857 / MPC862) Hardware Specifications
Manufacturer
Motorola
Datasheet
1.MPC857DSL.pdf
(88 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MPC857DSLCVR66B
Manufacturer:
Freescale Semiconductor
Quantity:
135
Company:
Part Number:
MPC857DSLCVR66B
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MPC857DSLCZQ66B
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MPC857DSLVR50B
Manufacturer:
Freescale Semiconductor
Quantity:
135
Company:
Part Number:
MPC857DSLVR50B
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MPC857DSLVR66B
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MPC857DSLZP50B
Manufacturer:
TI
Quantity:
101
Company:
Part Number:
MPC857DSLZQ50B
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
1
2
3
4
5
6
7
8
9
10
11
12
13
MOTOROLA
Num
B42 CLKOUT rising edge to TS valid (hold
B43 AS negation to memory controller
Phase and frequency jitter performance results are only valid if the input jitter is less than the prescribed value.
If the rate of change of the frequency of EXTAL is slow (I.e. it does not jump between the minimum and maximum
values in one cycle) or the frequency of the jitter is fast (I.e., it does not stay at an extreme value for a long time) then
the maximum allowed jitter on EXTAL can be up to 2%.
The timings specified in B4 and B5 are based on full strength clock.
The timing for BR output is relevant when the MPC862/857T/857DSL is selected to work with external bus arbiter.
The timing for BG output is relevant when the MPC862/857T/857DSL is selected to work with internal bus arbiter.
For part speeds above 50MHz, use 9.80ns for B11a.
The timing required for BR input is relevant when the MPC862/857T/857DSL is selected to work with internal bus
arbiter. The timing for BG input is relevant when the MPC862/857T/857DSL is selected to work with external bus
arbiter.
For part speeds above 50MHz, use 2ns for B17.
The D(0:31) and DP(0:3) input timings B18 and B19 refer to the rising edge of the CLKOUT in which the TA input
signal is asserted.
For part speeds above 50MHz, use 2ns for B19.
The D(0:31) and DP(0:3) input timings B20 and B21 refer to the falling edge of the CLKOUT. This timing is valid only
for read accesses controlled by chip-selects under control of the UPM in the memory controller, for data beats where
DLT3 = 1 in the UPM RAM words. (This is only the case where data is latched on the falling edge of CLKOUT.)
The timing B30 refers to CS when ACS = 00 and to WE(0:3) when CSNT = 0.
The signal UPWAIT is considered asynchronous to the CLKOUT and synchronized internally. The timings specified
in B37 and B38 are specified to enable the freeze of the UPM output signals as described in Figure 19.
The AS signal is considered asynchronous to the CLKOUT. The timing B39 is specified in order to allow the behavior
specified in Figure 22.
time) (MIN = 0.00 x B1 + 2.00)
signals negation (MAX = TBD)
Characteristic
MPC862/857T/857DSL Hardware Specifications
Freescale Semiconductor, Inc.
Table 7. Bus Operation Timings (continued)
For More Information On This Product,
Go to: www.freescale.com
2.00
Min
—
33 MHz
Max
TBD
—
2.00
Min
—
40 MHz
TBD
Max
—
2.00
Min
—
50 MHz
Max
TBD
—
Bus Signal Timing
2.00
Min
—
66 MHz
Max
TBD
—
Unit
ns
ns
23