SC16C750B Philips Semiconductors, SC16C750B Datasheet - Page 40

no-image

SC16C750B

Manufacturer Part Number
SC16C750B
Description
5 V/ 3.3 V and 2.5 V UART with 64-byte FIFOs
Manufacturer
Philips Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SC16C750BIA44
Manufacturer:
PHILIPS
Quantity:
886
Part Number:
SC16C750BIA44,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C750BIA44,518
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C750BIA44,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C750BIB64,128
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C750BIB64,151
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C750BIB64157
Manufacturer:
NXP Semiconductors
Quantity:
135
Part Number:
SC16C750BIBS
Manufacturer:
BCD
Quantity:
738
Company:
Part Number:
SC16C750BIBS
Quantity:
980
Philips Semiconductors
12. Soldering
9397 750 14453
Product data
12.1 Introduction to soldering surface mount packages
12.2 Reflow soldering
12.3 Wave soldering
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages (document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended. In these situations
reflow soldering is recommended.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270 C depending on solder
paste material. The top-surface temperature of the packages should preferably be
kept:
Moisture sensitivity precautions, as indicated on packing, must be respected at all
times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
below 225 C (SnPb process) or below 245 C (Pb-free process)
below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with
a thickness < 2.5 mm and a volume < 350 mm
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a volume
thick/large packages.
Rev. 03 — 13 December 2004
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
2.5 mm
3
so called small/thin packages.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
SC16C750B
350 mm
3
so called
40 of 44

Related parts for SC16C750B