SY3120 SMC, SY3120 Datasheet - Page 158

• Manufacturer Part Number: SY3120
• Description: 2 position single
• Manufacturer: SMC

Fitting Assembly Part No.
Note 1) When there are 10 or fewer manifold block assemblies, and more are
Note 2) When disassembly and assembly are performed, air leakage may
Note 3) One connector assembly is necessary for one solenoid.
Type 45 manifold permits change in the A and B port sizes by
changing the manifold block fitting assembly.
After removing the valve, remove the clip with a screwdriver, etc. For
mounting a new fitting assembly, insert it and then insert a clip until it
will not come out of the manifold block.
Metric size
Inch size
1
2
3
4
5
How to Increase Manifold Bases
How to Change Fitting Assembly
SY3000
SY5000
SY3000
SY5000
Caution
Loosen DIN rail holding screw
begins to turn idly. (While pressing DIN rail releasing buttons
at two locations, separate the manifold base from the DIN rail.)
Press manifold block assembly dividing button
location where manifold bases are to be added, until button
locks, and then separate the block assemblies.
Mount additional manifold block assembly on the DIN rail as
shown in the figure 1.
Press the block assemblies until a click sound is produced, and
tighten the DIN rail holding screw
(While lightly holding the blocks after fixing an end block on one
side, tighten the other end block for for better sealing.)
Untighten the rail stopper bolt
from the DIN rail, and when remounting it, tighten the bolt while
pressing it against the rail.
Caution (Tightening torque: 1.4 N·m)
Note 1) P and R ports cannot be changed.
Note 2) Use caution that O-rings must be free from scratches and dust.
added to make a total of 11 or more, a supply/exhaust block assembly
must also be added.
result if connections between blocks and tightening of the end block’s
holding screw, is inadequate. Before supplying air, confirm that there
are no gaps, etc. between blocks, and that manifold blocks are
securely fastened to the DIN rail. Then supply air and confirm that
there is no air leakage before operating.
suffix the number to the part no. (0 to 15 are provided as mark tube
numbers.)
When a number is necessary for the connector assembly mark tube,
Ex) +COM spec.: D type for 2 to 8 stations: No. 10
SY3000-43-1A-10
Otherwise, air leakage may result.
One-touch fitting for ø4
One-touch fitting for ø6
One-touch fitting for ø4
One-touch fitting for ø6
One-touch fitting for ø8
One-touch fitting for ø
One-touch fitting for ø
One-touch fitting for ø
One-touch fitting for ø
One-touch fitting for ø
D
a
5 32
1 4
5 32
5 16
1 4
fixing the manifold base until it
a
to demount the connector box
"
"
"
"
"
to fix them to the DIN rail.
VVQ1000-50A-C4
VVQ1000-50A-C6
VVQ1000-51A-C4
VVQ1000-51A-C6
VVQ1000-51A-C8
VVQ1000-50A-N3
VVQ1000-50A-N7
VVQ1000-51A-N3
VVQ1000-51A-N7
VVQ1000-51A-N9
b
Base Mounted
, that are at the
c
b
,
Series
Fig. (1) Block mounting procedure
SY3000/5000
Station expansion is possible at any position.
O ring
Clip
Hook the DIN rail here
and press down in the
direction of the arrow
until a click sound is
heard.
Fitting assembly
Type
45-
263
A
NA
SJ
SY
SV
SYJ
SZ
VP4
S0700
VQ
VQ4
VQ5
VQC
VQZ
SQ
VFS
VFR
VQ7