MC2340 ETC1 [List of Unclassifed Manufacturers], MC2340 Datasheet - Page 36
![no-image](/images/no-image-200.jpg)
MC2340
Manufacturer Part Number
MC2340
Description
Technical Specifications for Brushless Servo Motion Control
Manufacturer
ETC1 [List of Unclassifed Manufacturers]
Datasheet
1.MC2340.pdf
(59 pages)
Pin Name and
number
PosLim3/
Synch
NC/PosLim3
NegLim1
NegLim2
NegLim3
NegLim4
AxisOut1
AxisOut2
AxisOut3
AxisOut4
AxisIn1
AxisIn2
AxisIn3
AxisIn4
Hall1A
Hall1B
Hall1C
Hall2A
Hall2B
Hall2C
Hall3A
Hall3B
Hall3C
Hall4A
Hall4B
Hall4C
54
45
64
66
55
51
94
95
96
97
72
100
106
67
73
90
91
101
102
105
107
108
109
68
69
70
Direction
input/output
input
input
output
input
Input
Description
On the MC2340 chipset, this pin is the positive-side (forward) travel limit switch
for axis#3. On the MC2320 and MC2310 chipsets this pin is not used.
On the MC23x3 chipset, this pin is the synchronization signal. In the disabled
mode, the pin is configured as an input and is not used. In the master mode, the
pin outputs a synchronization pulse that can be used by slave nodes or other
devices to synchronize with the internal chip cycle of the master node. In the
slave mode, the pin is configured as an input and a pulse on the pin synchronizes
the internal chip cycle.
WARNING! If a valid axis limit pin is not used, its signal should
be tied high.
On the MC23x0 chipset, this pin is not used.
On the MC2343 chipset, this pin is the positive-side (forward) travel limit switch
for axis#3. On the MC2323 and MC2313 chipsets this pin is not used.
WARNING! If a valid axis limit pin is not used, its signal should
be tied high.
These signals provide inputs from the negative-side (reverse) travel limit
switches. On power-up or Reset these signals default to active low interpretation,
but the interpretation can be set explicitly using the
For MC2340 all 4 pins are valid. For MC2320 only NegLim1 and NegLim2 are
valid. For MC2310 only NegLim1 is valid.
WARNING! If a valid axis pin is not used, its signal must be tied
high. NegLim1 is an output during device reset and as such any
connection to GND or V
Invalid axis pins may also be left unconnected.
Each of these pins can be conditioned to track the state of any bit in the Status
registers associated with its axis.
For MC2340 all 4 pins are valid. For MC2320 only AxisOut1 and AxisOut2 are
valid. For MC2310 only AxisOut1 is valid.
Invalid or unused pins may be left unconnected.
These are general-purpose programmable inputs. They may be used as a
breakpoint input, to stop a motion axis, or to cause an UPDATE to occur.
For MC2340 all 4 pins are valid. For MC2320 only AxisIn1 and AxisIn2 are valid.
For MC2310 only AxisIn1 is valid.
Invalid or unused pins may be left unconnected.
Hall sensor inputs. Each set (A, B, and C) of signals encodes 6 valid states as
follows: A on, A and B on, B on, B and C on, C on, C and A on. A sensor is
defined as being on when its signal is high.
Note: These signals should only be connected to Hall sensors that are mounted
at a 120° offset. Schemes which provide Hall signals 60° apart will not work.
For MC2340 all 12 pins are valid. For MC2320 only the first six pins (axes 1 and
2) are valid. For MC2310 only the first three pins (axis 1) are valid.
Invalid or unused pins may be left unconnected.
MC2300 Technical Specifications
36
CP chip
cc
must be via a series resistor.
SetSignalSense
instruction.