acpm-5017 Avago Technologies, acpm-5017 Datasheet
acpm-5017
Available stocks
Related parts for acpm-5017
acpm-5017 Summary of contents
Page 1
... LTE Band12/17 (698-716 MHz Power Amplifier Module Data Sheet Description The ACPM-5017 is a fully matched 10-pin surface mount module developed for LTE Band12 and Band 17. This power amplifier module operates in the 698-716MHz bandwidth. The ACPM-5017 meets stringent LTE (MPR=0dB) linearity requirements ...
Page 2
Absolute Maximum Ratings No damage assuming only one parameter is set at limit at a time with all other parameters set at or below nominal value. Operation of any single parameter outside these conditions with the remaining parameters set at ...
Page 3
Electrical Characteristics – Conditions: Vcc = 3.4 V, Ven = 2 25° C, Zin/Zout = 50 ohm Characteristics Operating Frequency Range Maximum Output Power (High Power Mode) Gain Power Added Efficiency Total Supply Current Quiescent Current Enable ...
Page 4
Footprint All dimensions are in millimeter 1.50 0.10 Pin 1 0.25 0.3 X-RAY TOP VIEW Pin Description Pin # Name Description 1 Vcc1 DC Supply Voltage 2 RFin RF Input 3 Vbp Bypass Control 4 Vmode Mode Control 5 Ven ...
Page 5
Marking Specification Pin 1 Mark A5017 PYYWW AAAAA Metallization on 0.5 mm pitch Ø 0.3 mm 0.45 0.30 0.60 0.35 0.475 connected to a inner layer 0.55 through a via hole for a better isolation between CPL_IN(ISO) and RFout Solder ...
Page 6
Evaluation Board Schematic Vcc1 1 Vcc1 C5 C4 2.2 µ 680 Vbp 3 Vbp C3 100 pF Vmode 4 Vmode C2 100 pF Ven 5 Ven C1 100 pF Evaluation Board Description C3 C2 ...
Page 7
... Application for APT Application Information The use converter can enhance the efficiency of the ACPM-50xx PAs and this note presents an example of their APT applications system. 1. The Vcc1 pin of PAs is directly connected to a battery or the phone power The Vcc2 pin of PAs can be adjusted to its lowest value according to Tx average power level over discrete intervals that still meets the linearity requirements (e.g., ACLR1 -39 dBc @ Rel’ ...
Page 8
... Vcc2 is continuously adjusted based on the output power requirement of the PA. The voltage to the Vcc2 can be lowered to a point where the PA meets the linearity re- quirement. Average power tracking with ACPM-50xx PAs allows significant power saving as shown in the data here (the battery current vs. Tx output power with / without APT) ...
Page 9
... NOTES: 1. Reel shall be labeled with the following information (as a minimum). a. manufacturers name or symbol b. Avago Technologies part number c. purchase order number d. date code e. quantity of units 2. A certificate of compliance ( shall be issued and accompany each shipment 1.5 min. of product. 3. Reel must not be made with or contain 13.0 ± ...
Page 10
... After this time period, the part would need to be removed from the reel, de-taped and then re-baked. MSL classification reflow temperature for the ACPM-5017 is targeted at 260° C +0/-5° C. Figure and table on next page show typical SMT profile for maximum temperature of 260 +0/-5° C. ...
Page 11
Reflow Profile Recommendations smax T smin t s Preheat 25 t 25° Peak Typical SMT Reflow Profile for Maximum Temperature = 260 +0/-5° C Typical SMT Reflow Profile for Maximum Temperature = 260 ...
Page 12
Storage Condition Packages described in this document must be stored in sealed moisture barrier, antistatic bags. Shelf life in a sealed moisture barrier bag is 12 months at < 40° C and 90% relative humidity (RH) J-STD-033 p.7. Out-of-Bag Time ...
Page 13
... Level 5a For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. AV02-3006EN - August 31, 2011 ...