av9173-01cs08 Holt Integrated Circuits, Inc., av9173-01cs08 Datasheet

no-image

av9173-01cs08

Manufacturer Part Number
av9173-01cs08
Description
Video Genlock
Manufacturer
Holt Integrated Circuits, Inc.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AV9173-01CS08
Manufacturer:
ICS
Quantity:
20 000
The AV9173-01 provides the analog circuit blocks required
for implementing a video genlock dot (pixel) clock
generator. It contains a phase detector, charge pump, loop
filter, and voltage-controlled oscillator (VCO). By grouping
these critical analog blocks into one IC and utilizing
external digital functions, performance and design
flexibility are optimized as are development time and
system cost.
When used with an external clock divider, the AV9173-01
forms a Phase-Locked Loop configured as a frequency
synthesizer. The AV9173-01 is designed to accept video
horizontal synchronization (h-sync) pulses and produce a
video dot clock. A separated, negative-going sync input
reference pulse is required at pin 2 (I N).
The AV9173-01 is also suited for other clock recovery
applications in such areas as data communications.
Block Diagram
General Description
Video Genlock PLL
AV9173-01RevC052197P
Integrated
Circuit
Systems, Inc.
ICS reserves the right to make changes in the device data identified in this
publication without further notice. ICS advises its customers to obtain the latest
version of all device data to verify that any information being relied upon by the
customer is current and accurate.
Features
Phase-detector/VCO circuit block
Ideal for genlock system
Reference clock range 25 kHz to 1 MHz for full
output clock range
Input clocks down to 12 kHz possible with restricted
output conditions (see Table 1)
Output clock range 1.25 to 75 MHz
On-chip loop filter
Single 5 volt power supply
Low power CMOS technology
Small 8-pin DIP or SOIC package
AV9173-01

Related parts for av9173-01cs08

av9173-01cs08 Summary of contents

Page 1

... When used with an external clock divider, the AV9173-01 forms a Phase-Locked Loop configured as a frequency synthesizer. The AV9173-01 is designed to accept video horizontal synchronization (h-sync) pulses and produce a video dot clock ...

Page 2

... AV9173-01 Pin Configuration 8-Pin DIP or SOIC Pin Descriptions PIN PIN NAME NUMBER 1 FBIN GND 4 FS0 CLK1 7 VDD 8 CLK2 Table 1: Allowable Input Frequency to Output Frequency f (kHz) IN CLK1 Output kHz 44 kHz 30 kHz 25 ...

Page 3

... Refer to Application Brief (AB01) for additional details on use of input frequencies below 25kHz. By following the guidelines in this brief and meeting the test conditions in the Figure 1: Typical Application of AV9173- Video Genlock System AC specifications (VCO frequency), an input as low as 12kHz (such as NTSC or PAL h-sync) can be used. ...

Page 4

... AV9173-01 Absolute Maximum Ratings V (referenced to GND 7 Operating Temperature under Bias . . . . . . . . . 0°C to +70° C Storage Temperature . . . . . . . . . . . . . . . . . . . . – 65°C to +150°C Voltage on I/O pins referenced to GND . . . . . GND – 0 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . 0.5 watts Stresses above those listed under Absolute Maximum Ratings above may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied ...

Page 5

... CLK1 frequency applies for For condition, divide allowable CLK1 range by the factor Application Brief (AB01) documents the operation of the AV9173 for low input frequencies. This provides guidelines for usable output frequencies and feedback ratios required to use inputs below 25 kHz. By following these guidelines, the AV9173 will operate down to 12 kHz inputs across temperature, voltage and lot-to-lot variation ...

Page 6

... AV9173-01 Ordering Information AV9173-01CN08 - or - AV9173-01CS08 Example: XXX XXXX - PPP M X#W 8-Pin DIP PACKAGE 8-Pin SOIC PACKAGE Lead Count & Package Width Lead Count = digits W = 0.3" SOIC or 0.6" DIP; None = Standard Width Package Type N = DIP (Plastic SOIC Pattern Number ( digit number for parts with ROM code patterns) ...

Related keywords