L6100200 SEMIKRON [Semikron International], L6100200 Datasheet

Page 1

... SKYPER™ 32PRO - SKYPER™ 32PRO -------------------------------------------------------------------------------------------------------------------------------------------------------------------------- This Technical Explanation is valid for the following parts: part number L6100200 Related documents: title Data Sheet SKYPER™ 32PRO Prepared by: Markus Hermwille -------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Content Application and Handling Instructions...................................................................................................................... 2 Further application support ...................................................................................................................................... 2 General Description................................................................................................................................................. 2 Features of SKYPER™ 32PRO............................................................................................................................... 2 Block diagram ...

Page 2

SKYPER™ 32PRO - Please note: All values in this technical explanation are typical values. Typical values are the average values expected in large quantities and are provided for information purposes only. These values can and do vary in different applications. ...

Page 3

SKYPER™ 32PRO - Block diagram Block diagram Dimensions Dimensions Technical Explanations 2005-06-03 – Rev02 © by SEMIKRON ...

Page 4

SKYPER™ 32PRO - PIN Array – Primary Side Connectors PIN Signal X10:01 PRIM_nPWRFAIL_IN X10:02 reserved X10:03 PRIM_HALT_OUT X10:04 PRIM_HALT_IN X10:05 PRIM_PWR_GND X10:06 PRIM_PWR_GND X10:07 PRIM_TOP_IN X10:08 PRIM_BOT_IN X10:09 PRIM_PWR_15P X10:10 PRIM_PWR_15P X11:01 reserved X11:02 reserved X11:03 PRIM_PWR_GND X11:04 PRIM_PWR_GND X11:05 ...

Page 5

SKYPER™ 32PRO - PIN Array – Secondary Side Connectors PIN Signal X100:01 SEC_TOP_VCE_CFG X100:02 SEC_TOP_VCE_IN X100:03 SEC_TOP_15P X100:04 SEC_TOP_ERR_IN X100:05 SEC_TOP_IGBT_ON X100:06 SEC_TOP_IGBT_OFF X100:07 SEC_TOP_GND X100:08 SEC_TOP_GND X100:09 SEC_TOP_IGBT_SOFTOFF X100:10 SEC_TOP_8N X200:01 SEC_BOT_VCE_CFG X200:02 SEC_ BOT_VCE_IN X200:03 SEC_ BOT_15P X200:04 ...

Page 6

... The charge necessary to switch the IGBT is mainly depending on the IGBT’s chip size, the DC-link voltage and the gate voltage. This correlation is shown in module datasheets. It should, however, be considered that the driver is turned on at +15V and turned off at -7V. Therefore, the gate voltage will change by 22V during each switching procedure ...

Page 7

SKYPER™ 32PRO - characteristic or hiccup-mode can create problems if no sufficient over current margin is available. The voltage has to rise continuously and without any plateau formation as shown in the following diagram. Rising slope of the power supply ...

Page 8

SKYPER™ 32PRO - Under Voltage Protection (UVP) primary The internally detected supply voltage of the driver has an under voltage protection. The table below gives an overview of the trip level. Supply voltage Regulated +15V ±4% If the internally detected ...

Page 9

SKYPER™ 32PRO - Short Pulse Suppression (SPS) This circuit suppresses short turn-on and off-pulses of incoming signals. This way the IGBTs are protected against spurious noise as they can occur due to bursts on the signal lines. Pulses shorter than ...

Page 10

SKYPER™ 32PRO - Connection PRIM_HALT_OUT and PRIM_HALT_IN Please note: A HIGH signal @ PRIM_HALT_IN does not generate a HIGH signal @ PRIM_HOLD_OUT. After LOW signal @ PRIM_HALT_IN the gate driver is enable do operate. Dead Time generation (Interlock TOP / ...

Page 11

SKYPER™ 32PRO - Please note: The dead time has to be longer than the turn-off delay time of the IGBT in any case. This is to avoid that one IGBT is turned on before the other one is not completely ...

Page 12

SKYPER™ 32PRO - Adjustment of DSCP The external components R and C CE monitoring dynamic as well as the blanking time. Connection R and Application hints If the DSCP function is not used, for example during the ...

Page 13

SKYPER™ 32PRO - Gate resistors The output transistors of the driver are MOSFETs. The sources of the MOSFETs are separately connected to external terminals in order to provide setting of the turn-on and turn-off speed of each IGBT by the ...

Page 14

SKYPER™ 32PRO - External Error Input (EEI) The external error inputs on the secondary side (high potential) of the gate driver can be used for external fault signals from over current protection circuit or over temperature protection ...

Page 15

SKYPER™ 32PRO - Mounting Notes Soldering Hints The temperature of the solder must not exceed 260°C, and solder time must not exceed 10 seconds. The ambient temperature must not exceed the specified maximum storage temperature of the driver. The solder ...

Page 16

SKYPER™ 32PRO - Marking Every driver core is marked. The marking contains the following items. Part Marking Information 1. SEMIKRON part number (8 digits) + version number (2 digits) 2. Date code (4 digits): YYWW 3. Continuous number referred to ...