hdmp-1636 Avago Technologies, hdmp-1636 Datasheet
hdmp-1636
Available stocks
Related parts for hdmp-1636
hdmp-1636 Summary of contents
Page 1
... Low Power Consumption • Transmitter and Receiver Functions Incorporated onto a Single IC • Two Package Sizes Available: – PQFP (HDMP-1636) – PQFP (HDMP-1646) • 10-Bit Wide Parallel TTL Compatible I/Os • Single +3.3 V Power Supply • 5-Volt Tolerant I/Os • ESD Protection Applications • ...
Page 2
... PROTOCOL DEVICE BYTSYNC REFCLK ENBYTSYNC Figure 1. Typical Application Using the HDMP-16x6. DATA BYTE FRAME TX[0-9] TX TXCAP0 PLL/CLOCK TXCAP1 GENERATOR REFCLK RXCAP0 RXCAP1 RBC0 RBC1 FRAME DATA BYTE DEMUX RX[0-9] BYTE SYNC BYTSYNC Figure 2. HDMP-16x6 Transceiver Block Diagram. 712 HDMP-16x6 TRANSMITTER SECTION PLL PLL ...
Page 3
... Gigabit Ethernet specifi- cation, which uses an 8B/10B encoding scheme with special reserve characters for link management purposes. In order to accomplish this task, the HDMP-1636/46 incorporates the following: • TTL Parallel I/O’s • High Speed Phase Lock Loops • Clock Generation/Recovery Circuitry • ...
Page 4
... In order to accom- plish this, it uses the high speed serial clock recovered from the RX PLL/CLOCK RECOVERY block. This serial bit stream is sent to the FRAME DEMUX and BYTE SYNC block. HDMP-1636/46 (Transmitter Section) Timing Characteristics + 3. 3. ...
Page 5
REFCLK TX[0]-TX[9] DATA t SETUP Figure 3. Transmitter Section Timing. ± DOUT TX[0]-TX[9] REFCLK Figure 4. Transmitter Latency ...
Page 6
... HDMP-1636/46 (Receiver Section) Timing Characteristics + 3. 3. Symbol [1,2] b_sync Bit Sync Time t Time Data Valid Before Rising Edge of RBC valid_before t Time Data Valid After Rising Edge of RBC valid_after t RBC Duty Cycle duty t Rising Edge Time Difference A-B [3] t_rxlat ...
Page 7
... Symbol f Nominal Frequency (for Gigabit Ethernet Compliance) F Frequency Tolerance tol Symm Symmetry (Duty Cycle) HDMP-1636/46 (TRx) DC Electrical Specifications + 3. 3. Symbol V TTL Input High Voltage Level, Guaranteed High Signal IH,TTL for All Inputs ...
Page 8
... Output Peak-to-Peak Differential Voltage specified as DOUT+ minus DOUT-. a. Differential HS_OUT Output (Dout+ Minus Dout-). b. Single-Ended HS_OUT Output (Dout+). Eye Diagrams of the High-Speed Serial Outputs from the HDMP-1636/46 as Captured on the HP 83480A Digital Communications Analyzer. Tested with PRBS = 2 Figure 7. Transmitter DOUT Eye Diagrams. ...
Page 9
... HDMP-1646 by the max I and subtracting the power dissipated outside the chip at the high speed 3.45 volts. CC resistors and receiver TTL outputs driving 10 pF loads. for these devices is 48 C/Watt for the HDMP-1636 and 44 C/Watt for the Pd), where ...
Page 10
... Input TTL, Floats High When Left Open O-TTL Output TTL HS_OUT High Speed Output, ECL Compatible HS_IN High Speed Input C External Circuit Node S Power Supply or Ground HDMP-1636/46 (TRx) Pin Input Capacitance Symbol C Input Capacitance on TTL Input Pins INPUT O_TTL V _TTL ...
Page 11
... Rzz.zz = DIE REVISION S = SUPPLIER CODE YYWW = DATE CODE (YY = YEAR WORK WEEK) COUNTRY = COUNTRY OF MANUFACTURE (MARKED ON BACK OF DEVICE) Figure 11. HDMP-1636/46 (TRx) Package Layout and Marking, Top View. *Note: Pins 26 and 27 are designated as “no connect” pins and must be left unconnected ...
Page 12
TRx I/O Definition Name Pin Type BYTSYNC 47 O-TTL -DIN 52 HS_IN +DIN 54 -DOUT 61 HS_OUT Serial Data Outputs: High-speed outputs. These lines are active when +DOUT 62 ENBYTSYNC 24 I-TTL GND GND_RXA 51 S ...
Page 13
TRx I/O Definition (cont’d.) Name Pin Type RX[0] 45 O-TTL RX[1] 44 RX[2] 43 RX[3] 41 RX[4] 40 RX[5] 39 RX[6] 38 RX[7] 36 RX[8] 35 RX[9] 34 RXCAP0 48 C RXCAP1 49 TX[0] 2 I-TTL TX[1] 3 TX[2] 4 ...
Page 14
... Transceiver Power Supply Bypass and Loop Filter Capacitors Bypass capacitors should be liberally used and placed as close as possible to the appropriate power supply pins of the HDMP-1636/46 as shown on the schematic of Figure 12. All bypass chip capacitors are 0.1 F. The V _RXA and CC V _TXA pins are the analog ...
Page 15
... ALL DIMENSIONS ARE IN MILLIMETERS. PART NUMBER A1 HDMP-1636 10.00 HDMP-1646 14.00 TOLERANCE ± 0.10 ± 0.25 ± 0.05 BASIC + 0.15/ Figure 13. Mechanical Dimensions of HDMP-1636/46. Details Plastic 85% Tin, 15% Lead 300-800 m HDMP-1636 0.08 mm max HDMP-1646 0.10 mm max ...