mt18hvs25672rhy-667 Micron Semiconductor Products, mt18hvs25672rhy-667 Datasheet - Page 4

• Manufacturer Part Number: mt18hvs25672rhy-667
• Description: 2gb X72, Dr 200-pin Ddr2 Sdram Vlp Sordimm
• Manufacturer: Micron Semiconductor Products

Table 5:
PDF: 09005aef82882ad5/Source: 09005aef82882b0e
HVS18C_256x72RH.fm - Rev. B 5/08 EN
(DQS0#–DQS8#)
RAS#, CAS#,
DQS0–DQS8
DQ0–DQ63
DM0–DM8
CK0, CK0#
BA0–BA2
SA0–SA1
CB0–CB7
Symbol
A0–A13
EVENT#
RESET#
V
ODT0
CKE0
WE#
SDA
V
DDSPD
V
S0#
SCL
V
NC
REF
DD
SS
Pin Descriptions
(LVCMOS)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
(SSTL_18)
Output
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
I/O
–
On-die termination: ODT (registered HIGH) enables termination resistance internal to the
DDR2 SDRAM. When enabled, ODT is only applied to each of the following pins: DQ, DQS,
DQS#, and DM. The ODT input will be ignored if disabled via the LOAD MODE command.
Clock: CK and CK# are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and negative edge of CK#. Output data
(DQs and DQS/DQS#) is referenced to the crossings of CK and CK#.
Clock enable: CKE (registered HIGH) activates and CKE (registered LOW) deactivates
clocking circuitry on the DDR2 SDRAM.
Chip select: S# enables (registered LOW) and disables (registered HIGH) the command
decoder. All commands are masked when S# is registered HIGH. S# provides for external rank
selection on systems with multiple ranks. S# is considered part of the command code.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command being
entered.
Bank address inputs: BA0–BA2 define to which device bank an ACTIVE, READ, WRITE, or
PRECHARGE command is being applied. BA0–BA2 define which mode register including MR,
EMR, EMR(2), and EMR(3) is loaded during the LOAD MODE command.
Address inputs: Provide the row address for ACTIVE commands, and the column address
and auto precharge bit (A10) for READ/WRITE commands, to select one location out of the
memory array in the respective bank. A10 sampled during a PRECHARGE command
determines whether the PRECHARGE applies to one device bank (A10 LOW, device bank
selected by BA0–BA2) or all device banks (A10 HIGH). The address inputs also provide the op-
code during a LOAD MODE command.
Input data mask: DM is an input mask signal for write data. Input data is masked when DM
is sampled HIGH along with that input data during a WRITE access. DM is sampled on both
edges of DQS. Although DM pins are input-only, the DM loading is designed to match that
of DQ and DQS pins.
Serial clock: SCL is used to synchronize the presence-detect and temperature sensor data
transfer to and from the module.
Serial address inputs: These pins are used to configure the presence-detect and
temperature sensor devices.
Disables the output clocks on the PLL when LOW.
Data input/output: Bidirectional data bus.
Check bits.
Data strobe: Output with read data, input with write data for source synchronous
operation. Edge-aligned with read data, center aligned with write data. DQS# is only used
when differential data strobe mode is enabled via the LOAD MODE command.
Serial data: SDA is a bidirectional pin used to transfer addresses and data into and out of
the presence-detect and temperature sensor devices.
Temperature sensor alarm output.
Power supply: +1.8V ±0.1V.
SSTL_18 reference voltage.
Ground.
Serial EEPROM and temperature sensor positive power supply: +3.0V to +3.6V.
No connect: These pins should be left unconnected.
2GB (x72, DR) 200-Pin DDR2 SDRAM VLP SORDIMM
4
Description
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Pin Assignments and Descriptions
©2007 Micron Technology, Inc. All rights reserved.