scn68562 NXP Semiconductors, scn68562 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
scn68562
Manufacturer Part Number
scn68562
Description
Dual Universal Serial Communications Controller Duscc
Manufacturer
NXP Semiconductors
Datasheet
1.SCN68562.pdf
(18 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
scn68562C4A52
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
scn68562C4N28
Manufacturer:
PHI
Quantity:
6 244
Company:
Part Number:
scn68562C4N48
Manufacturer:
MOT
Quantity:
6 227
Part Number:
scn68562C4N48
Manufacturer:
PHI
Quantity:
20 000
Philips Semiconductors
PIN DESCRIPTION
In this data sheet, signals are discussed using the terms ‘active’ and ‘inactive’ or ‘asserted’ and ‘negated’ independent of whether the signal is
active in the High (logic 1) or Low (logic 0) state. N at the end of a pin name signifies the signal associated with the pin is active-Low (see
individual pin description for the definition of the active level of each signal.) Pins which are provided for both channels are designated by A/B
after the name of the pin and the active-Low state indicator, N, if applicable. A similar method is used for registers provided for both channels:
these are designated by either an underline or by A/B after the name.
1995 May 01
A1 – A6
D0 – D7
R/WN
CSN
DTACKN
IRQN
IACKN
X1/CLK
X2/IDCN
RESETN
RxDA, RxDB
TxDA, TxDB
RTxCA, RTxCB
Dual universal serial communications controller (DUSCC)
MNEMONIC
PIN NO.
31-28,
37, 12
36, 13
39, 10
45-47
21-18
4-2,
DIP
26
25
22
43
42
6
1
7
TYPE
I/O
I/O
O
O
O
O
I
I
I
I
I
I
I
Address Lines: Active-High. Address inputs which specify which of the internal registers
is accessed for read/write operation.
Bidirectional Data Bus: Active High, 3-State. Bit 0 is the LSB and bit 7 is the MSB. All
data, command, and status transfers between the CPU and the DUSCC take place over
this bus. The data bus is enabled when CSN is Low, during interrupt acknowledge cycles
and single-address DMA acknowledge cycles.
Read/Write: A High input indicates a read cycle and a Low input indicates a write cycle
when a cycle is initiated by assertion of the CSN input.
Chip Select: Active-Low input. When Low, data transfers between the CPU and the
DUSCC are enabled on D0 – D7 as controlled by the R/WN and A1 – A6 inputs. When
CSN is High, the DUSCC is isolated from the data bus (except during interrupt
acknowledge cycles and single-address DMA transfers) and D0 – D7 are placed in the
3-State condition.
Data Transfer Acknowledge: Active-Low, 3-State. DTACKN is asserted on a write cycle
to indicate that the data on the bus has been latched, and on a read cycle or interrupt
acknowledge cycle to indicate valid data is on the bus. The signal is negated when
completion of the cycle is indicated by negation of the CSN or IACKN input, and returns to
the inactive state (3-State) a short period after it is negated. In a single address DMA
mode, data is latched with the falling edge of DTCN. DTACKN is negated when
completion of the cycle is indicated by the assertion of DTCN or negation of DMA
acknowledge inputs (whichever occurs first), and returns to the inactive state (3-State) a
short period after it is negated. When negated, DTACKN becomes an open-drain output
and requires an external pull-up resistor.
Interrupt Request: Active-Low, open-drain. This output is asserted upon occurrence of
any enabled interrupting condition. The CPU can read the general status register to
determine the interrupting condition(s), or can respond with an interrupt acknowledge cycle
to cause the DUSCC to output an interrupt vector on the data bus.
Interrupt Acknowledge: Active-Low. When IACKN is asserted, the DUSCC responds by
placing the contents of the interrupt vector register (modified or unmodified by status) on
the data bus and asserting DTACKN. If no active interrupt is pending, DTACKN is not
asserted.
Crystal or External Clock: When using the crystal oscillator, the crystal is connected
between pins X1 and X2. If a crystal is not used, and external clock is supplied at this
input. This clock is used to drive the internal bit rate generator, as an optional input to the
counter/timer or DPLL, and to provide other required clocking signals.
Crystal or Interrupt Daisy Chain: When a crystal is used as the timing source, the
crystal is connected between pins X1 and X2. This pin can be programmed to provide and
interrupt daisy chain active-Low output which propagates the IACKN signal to lower priority
devices, if no active interrupt is pending. This pin should be grounded when an external
clock is used on X1 and X2, is not used as an interrupt daisy chain output.
Master Reset: Active-Low. A low on this pin resets the transmitters and receivers and
resets the registers shown in Table 1 of the CDUSCC Users’ Guide. Reset in
asynchronous, i.e., no clock is required.
Channel A (B) Receiver Serial Data Input: The least significant bit is received first. If
external receiver clock is specified for the channel, the input is sampled on the rising edge
of the clock.
Channel A (B) Transmitter Serial Data Output: The least significant bit is transmitted
first. This output is held in the marking (High) condition when the transmitter is disabled or
when the channel is operating in local loopback mode. If external transmitter clock is
specified for the channel, the data is shifted on the falling edge of the clock.
Channel A (B) Receiver/Transmitter Clock: As an input, it can be programmed to
supply the receiver, transmitter, counter/timer, or DPLL clock. As an output, can supply the
counter/timer output, the transmitter shift clock (1X), or the receiver sampling clock (1X).
The maximum external receiver/transmitter clock frequency is 4MHz.
5
NAME AND FUNCTION
SCN68562
Product specification