emc2105 Standard Microsystems Corp., emc2105 Datasheet - Page 23

• Manufacturer Part Number: emc2105
• Description: Emc2105 Rpm-based High Side Fan Controller With Hardware Thermal Shutdown
• Manufacturer: Standard Microsystems Corp.

RPM-Based High Side Fan Controller with Hardware Thermal Shutdown
Datasheet
APPLICATION NOTE: If the SHDN_SEL pin is pulled to ‘1’ at power up and the TRIP_SET / VIN4 pin is intended
APPLICATION NOTE: If the SHDN_SEL pin is pulled to ‘1’ at power up and the TRIP_SET / VIN4 pin is intended
APPLICATION NOTE: When used in its TRIP_SET mode (i.e. the SHDN_SEL pin is not set to a logic ‘1’), current
SMSC EMC2105
5.1.1
5.1.2
High-Z (open)
SHDN_SEL
0
1
SHDN_SEL Pin
The EMC2105 has a ‘strappable’ input (SHDN_SEL) allowing for configuration of the hardware
Critical/Thermal Shutdown input channels. This pin has 3 possible states and is monitored and
decoded by the EMC2105 at power-up. The three possible states are 0 (tied to GND), 1 (tied to 3.3V)
or High-Z (open). The state of this pin determines which external diode configuration is used for the
Critical / Thermal shutdown function.
The different configurations of the SHDN_SELpin are described in
to the selected temperature channel.
TRIP_SET / VIN4 Pin
The EMC2105’s TRIP_SET / VIN4 pin is an analog input to the Critical/Thermal Shutdown block which
sets the Thermal Shutdown temperature. The system designer creates a voltage level at the input
through a simple resistor connected to GND as shown in
to create an input voltage on the TRIP_SET / VIN4 pin which is translated into a temperature ranging
from 60°C to 122°C or 90°C to 152°C as enumerated in
When the SHDN_SEL pin is pulled to ‘1’ at power up, then the TRIP_SET / VIN4 pin is configured to
measure VIN4 as its primary function. The circuitry will still calculate the thermal / critical shutdown
threshold based on the voltage and compare this temperature against the Internal Diode temperature.
This will cause the SYS_SHDN# pin to assert if the measured temperature exceeds this threshold.
The device will also compare the measured voltage against the VIN4 High and Low limits. This function
is not available if SHDN_SEL is set to ‘0’ or ‘High-Z’ at power up.
Intel Transistor
Mode (substrate
PNP)
AMD CPU /
Diode Mode
Internal
for use as a voltage input then the SYS_SHDN# pin should be ignored.
to be used to set a threshold level then the VIN4 channel should be masked. Furthermore,
the voltage on the pin must be externally generated based on
Table
only flows when the TRIP_SET / VIN4 pin is being monitored. At all other times, the internal
reference voltage is removed and the TRIP_SET / VIN4 pin will be pulled down to ground.
FUNCTION
NAME
5.2.
Table 5.1 SHDN_SEL Pin Configuration
The external diode 1 channel is configured with
Beta Compensation enabled and Resistance
Error Correction enabled. This mode is ideal
for monitoring a substrate transistor such as an
Intel CPU thermal diode.
The external diode 1channel is configured with
Beta Compensation disabled and Resistance
Error Correction disabled. This mode is ideal
for monitoring an AMD processor diode or a
2N3904 diode.
The internal diode is linked to the Hardware set
Thermal / Critical shutdown circuitry and the
SYS_SHDN# pin.
TEMPERATURE MONITORING FEATURES
DATASHEET
23
Table
Figure
5.2.
5.1. The value of this resistor is used
Table
5.1. SHDN_SEL applies only
Equation
CRITICAL / THERMAL
High - 92°C to 154°C
Low - 60°C to 122°C
Low - 60°C to 122°C
SHUTDOWN RANGE
Revision 1.74 (05-08-08)
[1]. Do not use