mc9s12xs128 Freescale Semiconductor, Inc, mc9s12xs128 Datasheet - Page 486

no-image

mc9s12xs128

Manufacturer Part Number
mc9s12xs128
Description
Hcs12 Microcontrollers 16-bit Automotive Microcontroller
Manufacturer
Freescale Semiconductor, Inc
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
mc9s12xs128CAA
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s12xs128CAA
Quantity:
37
Part Number:
mc9s12xs128CAE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc9s12xs128CAL
Manufacturer:
FREESCALE
Quantity:
3 050
Part Number:
mc9s12xs128CAL
Manufacturer:
FREESCALE
Quantity:
3 050
Part Number:
mc9s12xs128CAL
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s12xs128MAA
Manufacturer:
FREESCALE
Quantity:
4 000
Part Number:
mc9s12xs128MAA
Manufacturer:
FREESCALE
Quantity:
5 630
Part Number:
mc9s12xs128MAA
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc9s12xs128MAA
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s12xs128MAA
0
Part Number:
mc9s12xs128MAA 1M04M
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s12xs128MAE
Manufacturer:
INITIO
Quantity:
3 310
Part Number:
mc9s12xs128MAL
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s12xs128VAA
Quantity:
58
Timer Module (TIM16B8CV2)
Note: in
16.4.3.1
Internal register whose output drives OCx can be programmed before timer drives OCx. The desired state
can be programmed to this Internal register by writing a one to CFORCx bit with TIOSx, OCPDx and TEN
bits set to one. Setting OCPDx to zero allows Interal register to drive the programmed state to OCx. This
allows a glitch free switch over of port from general purpose I/O to timer output once the OCPDx bit is set
to zero.
16.4.4
The pulse accumulator (PACNT) is a 16-bit counter that can operate in two modes:
Event counter mode — Counting edges of selected polarity on the pulse accumulator input pin, PAI.
Gated time accumulation mode — Counting pulses from a divide-by-64 clock. The PAMOD bit selects the
mode of operation.
The minimum pulse width for the PAI input is greater than two bus clocks.
16.4.5
Clearing the PAMOD bit configures the PACNT for event counter operation. An active edge on the IOC7
pin increments the pulse accumulator counter. The PEDGE bit selects falling edges or rising edges to
increment the count.
The Pulse Accumulator counter register reflect the number of active input edges on the PACNT input pin
since the last reset.
The PAOVF bit is set when the accumulator rolls over from 0xFFFF to 0x0000. The pulse accumulator
overflow interrupt enable bit, PAOVI, enables the PAOVF flag to generate interrupt requests.
486
TC7 event
Figure
Pulse Accumulator
Event Counter Mode
TC7
OC Channel Initialization
The PACNT input and timer channel 7 use the same pin IOC7. To use the
IOC7, disconnect it from the output logic by clearing the channel 7 output
mode and output level bits, OM7 and OL7. Also clear the channel 7 output
compare 7 mask bit, OC7M7.
16-31,if PR[2:0] is equal to 0, one prescaler counter equal to one bus clock
prescaler
counter
Figure 16-31. The TCNT cycle diagram under TCRE=1 condition
0
S12XS Family Reference Manual, Rev. 1.10
1
NOTE
-----
TC7-1
TC7 event
1 bus
clock
TC7
Freescale Semiconductor
0

Related parts for mc9s12xs128