tc58fvt160 TOSHIBA Semiconductor CORPORATION, tc58fvt160 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/6/670/toshiba_semiconductor_corporation_sml.jpg)
tc58fvt160
Manufacturer Part Number
tc58fvt160
Description
16-mbit 2m ? 8 Bits / 1m ? 16 Bits Cmos Flash Memory
Manufacturer
TOSHIBA Semiconductor CORPORATION
Datasheet
1.TC58FVT160.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
tc58fvt160AFT-70
Manufacturer:
TOSHIBA
Quantity:
1 400
Part Number:
tc58fvt160AFT70
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
Company:
Part Number:
tc58fvt160ATG-70
Manufacturer:
ROHM
Quantity:
3 000
Company:
Part Number:
tc58fvt160ATG70
Manufacturer:
TOSHIBA
Quantity:
396
Company:
Part Number:
tc58fvt160AXB-70
Manufacturer:
TOSHIBA
Quantity:
720
Part Number:
tc58fvt160AXB-70
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
Company:
Part Number:
tc58fvt160FT-10
Manufacturer:
TOSHIBA
Quantity:
1 400
Part Number:
tc58fvt160FT-85
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
Auto-Program Mode
Program command. The program address is latched on the falling edge of the WE signal and data is latched on
the rising edge of the fourth Bus Write cycle (with WE control). Auto programming starts on the rising edge of
the WE signal in the fourth Bus Write cycle. The Program and Program Verify commands are automatically
executed by the chip. The device status during programming is indicated by the Hardware Sequence flag. To read
the Hardware Sequence flag, specify the address to which the Write is being performed
hardware reset. Note that if the Auto-Program operation is terminated in this manner, the data written so far is
invalid.
rising edge of the WE signal in the fourth Bus Write cycle.
return to Read Mode. The device status is indicated by the Hardware Sequence flag. Either a Reset command or
a hardware reset is required to return the device to Read Mode after a failure. If a programming operation fails,
the block which contains the address to which data could not be programmed should not be used.
cells which contain 0s. If this is attempted, execution of Auto Program will fail. This is a user error, not a device
error. A cell containing 0 must be erased in order to set it to 1.
Fast Program Mode
completed in two cycles. In this mode the first two cycles of the command sequence, which normally requires four
cycles, are omitted. Writing is performed in the remaining two cycles. To execute Fast Program, input the Fast
Program command. Write in this mode uses the Fast Program command but operation is the same at that for
ordinary Auto-Program. The status of the device is indicated by the Hardware Sequence flag and read operations
can be performed as usual. To exit this mode, the Fast Program Reset command must be input. When the
command is input, the device will return to Read Mode.
Program Suspend/Resume Mode
Program Suspend command in Write Mode (including Write operations performed during Erase Suspend) but
ignores the command in other modes. After input of the command, the device will enter Program Suspend Read
Mode after t
suspended, the address to which Write was being performed becomes undefined. ID Read and CFI Data Read are
the same as usual.
receiving the Resume command, the device returns to Write Mode and resumes outputting the Hardware
Sequence flag for the bank to which data is being written.
The TC58FVT160/B160A can be programmed in either byte or word units. Auto-Program Mode is set using the
During Auto-Program execution, a command sequence cannot be accepted. To terminate execution, use a
Any attempt to program a protected block is ignored. In this case the device enters Read Mode 3 µs after the
If an Auto-Program operation fails, the device remains in the programming state and does not automatically
The device allows 0s to be programmed into memory cells which contain a 1. 1s cannot be programmed into
Fast Program is a function which enables execution of the command sequence for the Auto Program to be
Program Suspend is used to enable Data Read by suspending the Write operation. The device accepts a
During Program Suspend, Cell Data Read, ID Read and CFI Data Read can be performed. When Data Write is
After completion of Program Suspend input a Program Resume command to return to Write Mode. On
Program Suspend can be run in Fast Program Mode.
SUSP
.
TC58FVT160/B160AFT/AXB-70,-10
.
2002-08-06 8/41