tc58fvm5t2a TOSHIBA Semiconductor CORPORATION, tc58fvm5t2a Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/6/670/toshiba_semiconductor_corporation_sml.jpg)
tc58fvm5t2a
Manufacturer Part Number
tc58fvm5t2a
Description
32mbit 4m U 8 Bits/2m U 16 Bits Cmos Flash Memory
Manufacturer
TOSHIBA Semiconductor CORPORATION
Datasheet
1.TC58FVM5T2A.pdf
(63 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
tc58fvm5t2aTG65
Manufacturer:
TOSHIBA
Quantity:
5 380
Company:
Part Number:
tc58fvm5t2aTG65
Manufacturer:
TOSHIBA
Quantity:
4 000
Part Number:
tc58fvm5t2aTG65
Manufacturer:
TOSHIBA/东芝
Quantity:
20 000
DQ6 (Toggle bit 1)
operation. The Toggle bit begins toggling on the rising edge of WE in the last bus cycle. DQ6 alternately
outputs a 0 or a 1 for each OE access while CE
has been completed, toggling stops and valid memory cell data can be read by subsequent reading. If the
operation fails, the DQ6 output toggles.
3 Ps. It will then stop toggling. If an attempt is made to execute an auto erase operation on a protected block,
DQ6 will toggle for around 250 Ps. It will then stop toggling. After toggling has stopped the device will return to
Read Mode.
DQ5 (internal time-out)
operation has not been completed within the allotted time.
outputs a 1. Either a hardware reset or a software Reset command is required to return the device to Read
Mode.
DQ3 (Block Erase timer)
command cycle. DQ3 outputs a 0 for the duration of the Block Erase Hold Time and a 1 when the Block Erase
operation starts. Additional Block Erase commands can only be accepted during the Block Erase Hold Time.
Each Block Erase command input within the hold time resets the timer, allowing additional blocks to be marked
for erasing. DQ3 outputs a 1 if the Program or Erase operation fails.
DQ2 (Toggle bit 2)
device is in Erase Suspend Mode.
Now 1 will be output from non-selected blocks; thus, the selected block can be ascertained. If data is read
continuously from the block selected for Auto Block Erase while the device is in Erase Suspend Mode, the DQ2
output will toggle. Because the DQ6 output is not toggling, it can be determined that the device is in Erase
Suspend Mode. If data is read from the address to which data is being written during Erase Suspend in
Programming Mode, DQ2 will output a 1.
(Busy state) indicates that an Auto-Program or auto-erase operation is in progress. A 1 (Ready state) indicates
that the operation has finished and that the device can now accept a new command.
an operation has failed.
1 during an Erase Suspend operation. The output buffer for the
allowing a wired-OR connection. A pull-up resistor must be inserted between V
RY
The device status can be determined by the Toggle Bit function during an Auto-Program or auto-erase
If an attempt is made to execute an Auto Program operation on a protected block, DQ6 will toggle for around
If the internal timer times out during a Program or Erase operation, DQ5 outputs a 1. This indicates that the
Any attempt to program a 1 into a cell containing a 0 will fail (see Auto-Program Mode). In this case DQ5
The Block Erase operation starts 50 Ps (the Erase Hold Time) after the rising edge of WE in the last
DQ2 is used to indicate which blocks have been selected for Auto Block Erase or to indicate whether the
If data is read continuously from the selected block during an Auto Block Erase, the DQ2 output will toggle.
TC58FVM5T2A/B2A/T3A/B3A has a
During an Auto Block Erase operation, commands other than Erase Suspend are ignored.
RY
/
BY
/
BY
(READY/
outputs a 0 after the rising edge of WE in the last command cycle.
BUSY
)
RY
/
BY
signal to indicate the device status to the host processor. A 0
V
IL
while the device is busy. When the internal operation
TC58FVM5(T/B)(2/3)A(FT/XB)65
RY
/
BY
pin is an open-drain type circuit,
DD
and the
RY
2003-01-29 19/63
/
BY
RY
RY
outputs a 0 when
/
BY
/
BY
pin.
outputs a