m24c32 STMicroelectronics, m24c32 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
m24c32
Manufacturer Part Number
m24c32
Description
64/32 Kbit Serial I??c Bus Eeprom
Manufacturer
STMicroelectronics
Datasheet
1.M24C32.pdf
(26 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
m24c32-FMB5TG
Manufacturer:
ST
Quantity:
500
Company:
Part Number:
m24c32-FMB5TG
Manufacturer:
MAXIM
Quantity:
142
Part Number:
m24c32-FMB5TG
Manufacturer:
ST
Quantity:
20 000
M24C64, M24C32
DEVICE OPERATION
The device supports the I
marized in
on to the bus is defined to be a transmitter, and
any device that reads the data to be a receiver.
The device that controls the data transfer is known
as the bus master, and the other as the slave de-
vice. A data transfer can only be initiated by the
bus master, which will also provide the serial clock
for synchronization. The M24Cxx device is always
a slave in all communication.
Start Condition
Start is identified by a falling edge of Serial Data
(SDA) while Serial Clock (SCL) is stable in the
High state. A Start condition must precede any
data transfer command. The device continuously
monitors (except during a Write cycle) Serial Data
(SDA) and Serial Clock (SCL) for a Start condition,
and will not respond unless one is given.
Stop Condition
Stop is identified by a rising edge of Serial Data
(SDA) while Serial Clock (SCL) is stable and driv-
en High. A Stop condition terminates communica-
tion between the device and the bus master. A
Read command that is followed by NoAck can be
followed by a Stop condition to force the device
into the Stand-by mode. A Stop condition at the
end of a Write command triggers the internal Write
cycle.
Acknowledge Bit (ACK)
The acknowledge bit is used to indicate a success-
ful byte transfer. The bus transmitter, whether it be
bus master or slave device, releases Serial Data
(SDA) after sending eight bits of data. During the
9
Table 6. Operating Modes
Note: 1. X =
8/26
Current Address Read
Random Address Read
Sequential Read
Byte Write
Page Write
th
clock pulse period, the receiver pulls Serial
V
Mode
Figure
IH
or V
IL
.
5.. Any device that sends data
2
C protocol. This is sum-
RW bit
1
0
1
1
0
0
WC
V
V
X
X
X
X
IL
IL
1
Data (SDA) Low to acknowledge the receipt of the
eight data bits.
Data Input
During data input, the device samples Serial Data
(SDA) on the rising edge of Serial Clock (SCL).
For correct device operation, Serial Data (SDA)
must be stable during the rising edge of Serial
Clock (SCL), and the Serial Data (SDA) signal
must change only when Serial Clock (SCL) is driv-
en Low.
Memory Addressing
To start communication between the bus master
and the slave device, the bus master must initiate
a Start condition. Following this, the bus master
sends the Device Select Code, shown in
(on Serial Data (SDA), most significant bit first).
The Device Select Code consists of a 4-bit Device
Type Identifier, and a 3-bit Chip Enable “Address”
(E2, E1, E0). To address the memory array, the 4-
bit Device Type Identifier is 1010b.
Up to eight memory devices can be connected on
a single I
code on the Chip Enable (E0, E1, E2) inputs.
When the Device Select Code is received, the de-
vice only responds if the Chip Enable Address is
the same as the value on the Chip Enable (E0, E1,
E2) inputs.
The 8
set to 1 for Read and 0 for Write operations.
If a match occurs on the Device Select code, the
corresponding device gives an acknowledgment
on Serial Data (SDA) during the 9
device does not match the Device Select code, it
deselects itself from the bus, and goes into Stand-
by mode.
Bytes
1
1
1
32
1
th
bit is the Read/Write bit (RW). This bit is
2
START, Device Select, RW = 1
START, Device Select, RW = 0, Address
reSTART, Device Select, RW = 1
Similar to Current or Random Address Read
START, Device Select, RW = 0
START, Device Select, RW = 0
C bus. Each one is given a unique 3-bit
Initial Sequence
th
bit time. If the
Table 3.