sab9082 NXP Semiconductors, sab9082 Datasheet
sab9082
Related parts for sab9082
sab9082 Summary of contents
Page 1
... DATA SHEET SAB9082 NTSC Picture-In-Picture (PIP) controller Preliminary specification Supersedes data of 1999 Feb 18 File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 1999 Nov 12 ...
Page 2
... Linear zoom in horizontal direction for the main channel Three multistandard PIP modes are available. GENERAL DESCRIPTION The SAB9082 is an NTSC PIP controller which can be used in double window applications. The SAB9082 inserts one or two live video signals with reduced size into another live video signal ...
Page 3
... V DDD(P1) V DDD(RL) V SSD(RM) V SSD(RP) V SSD(P2) V DDD( HORIZONTAL AND VERTICAL FILTER LINE MEMORY INTERNAL DRAM HORIZONTAL SAB9082 FILTER 2 I C-BUS CONTROL 29, 31 n.c. T7 SDA T6 POR SCL Fig.1 Block diagram. V DDA(SA) V DDA(SF) V DDD(SA) ...
Page 4
... I test clock input (CMOS levels) I test mode input (CMOS levels) I test control block data input (CMOS levels) I test control block clock input (CMOS levels) I test control block reset input (CMOS levels) S digital ground for test 4 Preliminary specification SAB9082 DESCRIPTION ...
Page 5
... ADCs I analog Y input for main channel I/O analog top reference voltage for main channel ADCs I analog V input for main channel 5 Preliminary specification SAB9082 DESCRIPTION 2 C-bus; CMOS levels tolerant) 2 C-bus tolerant) < SHSYNC < ...
Page 6
... V SSD(T2 DDD(RP) 20 n.c. 21 n.c. 22 n.c. 23 n.c. 24 n.c. 25 n.c. 26 n.c. 27 n. SSD(T3) 1999 Nov 12 SAB9082 Fig.2 Pin configuration. 6 Preliminary specification SAB9082 V ref(B)(SA DDA(SF SSA(SA DDA(SA POR 74 SDA 73 SCL 72 SVSYNC 71 DCLK 70 DVSYNC PKOFF 69 FBL 68 V DDD( SSD(D) ...
Page 7
... MAIN 1999 Nov 12 The starting-point of the acquisition can be controlled with the acquisition fine positioning added to a system constant. With a nominal input f signals, 1408 samples (active video) are acquired and processed by the SAB9082. Here, the nominal input f HSYNC 1792 SUB SUB MAIN ...
Page 8
... Data transfer may be initiated only when the bus is not 2 busy. The SAB9082 has the I C-bus address 2CH. Valid subaddresses are 00H to 18H, registers 15H to 18H are reserved for future extensions. ...
Page 9
Table 1 Overview of I C-bus addresses For a description of the various data bits, see the following pages SUB ADDRESS BIT 7 BIT 6 00H MPIPON SPIPON 01H SHBlow1 SHBlow0 02H SVBlow SVRed6 03H BGVfp3 BGVfp2 04H SDHfp7 ...
Page 10
... This can be realized by setting this bit to logic 1. Normally, bit AlgOff should be set to logic 0. DN ONINT In normal mode (this bit is logic 0), the SAB9082 calculates whether a signal is non-interlaced and reacts accordingly. With bit DNonint set to logic 1, the display channel is forced into the non-interlaced mode. In the non-interlaced mode, only one field is used during the processing of the PIPs ...
Page 11
... UV signals can be inverted when the decoder circuit before the SAB9082 emits inverted signals. With SVSPol set to logic 0, the SAB9082 triggers on positive edges of the SVSYNC set to logic 1, it triggers on the negative edges. Bit SFPol can invert the field ID of the incoming fields ...
Page 12
... When the input signals for the main and/or subchannel 0.5 pixel are non-interlaced, joint line errors can occur. When 1 pixel non-interlaced signals are input, the SAB9082 switches automatically to the non-interlaced mode. 2. When the prevent joint line error algorithm is switched off (AlgOff is set to logic 1), joint line errors can still ...
Page 13
... PARAMETER SYMBOL HUMAN BODY MODEL (V) FBL PKOFF DVSYNC SVSYNC SCL SDA all other pins standard specification 13 Preliminary specification SAB9082 , from the f , which is approximately HSYNC MIN. MAX. 0.5 5.0 25 +150 1.0 MACHINE MODEL (V) 1000 ...
Page 14
... Preliminary specification MIN. TYP. MAX. 3.0 3.3 3 100 0 100 0 50 0.4 0 140 165 210 50 2.70 2.82 2.95 0.95 1.07 1.20 1.00 1.04 1.05 1.10 1.33 1.38 0 1792 f HSYNC 1.4 +1.4 2.0 +2.0 48 1.25 1.34 1.45 1.80 1.93 2.15 SAB9082 UNIT kHz bit LSB LSB ...
Page 15
... HSYNC 15 Preliminary specification MIN. TYP. MAX. 1.10 1.20 1.30 0.15 0.23 0.30 1 1000 0 5 1792 f HSYNC 1.0 +1.0 1.0 +1 15. 15. DDA . They can be calculated with the formulas ref(T) ref(B) SAB9082 UNIT kHz bit LSB LSB dB kHz kHz ), which equals ...
Page 16
... V < > V 200 DDD 16 note the main channel and subchannel. HSYNC 16 Preliminary specification MIN. TYP. V DDD 5.5 DDD V 5.5 DDD 0.5 0.2V DDD 0.4 0 1792 f HSYNC SAB9082 MAX. UNIT + 0.5 V DDD ( DDD kHz ns ns ...
Page 17
... NTSC Picture-In-Picture (PIP) controller TEST AND APPLICATION INFORMATION Figure 5 gives the application diagram in a standard configuration. Input signals main channel CVBS and subchannel CVBS from different video sources are processed by the SAB9082 and inserted by the YUV to RGB switch. handbook, full pagewidth SUB ...
Page 18
... 0.40 0.25 20.1 14.1 24.2 0.65 0.25 0.14 19.9 13.9 23.6 REFERENCES JEDEC EIAJ 18 Preliminary specification 18.2 1.0 1.95 0.2 0.15 0.1 17.6 0.6 EUROPEAN PROJECTION SAB9082 SOT317 detail X (1) ( 0.8 1 0.4 0.6 0 ISSUE DATE 95-02-04 97-08-01 ...
Page 19
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 19 Preliminary specification SAB9082 ...
Page 20
... Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 1999 Nov 12 SOLDERING METHOD WAVE not suitable (2) suitable (3)(4) not recommended (5) not recommended 20 Preliminary specification SAB9082 (1) REFLOW suitable suitable suitable suitable suitable ...
Page 21
... I Philips. This specification can be ordered using the code 9398 393 40011. 1999 Nov components conveys a license under the Philips’ system provided the system conforms to the I 21 Preliminary specification SAB9082 2 C patent to use the 2 C specification defined by ...
Page 22
... Philips Semiconductors NTSC Picture-In-Picture (PIP) controller 1999 Nov 12 NOTES 22 Preliminary specification SAB9082 ...
Page 23
... Philips Semiconductors NTSC Picture-In-Picture (PIP) controller 1999 Nov 12 NOTES 23 Preliminary specification SAB9082 ...
Page 24
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + 101 ...