lan9211 Standard Microsystems Corp., lan9211 Datasheet - Page 137

• Manufacturer Part Number: lan9211
• Description: Lan9211 High-performance Small Form Factor Single-chip Ethernet Controller With Hp Auto-mdix Support
• Manufacturer: Standard Microsystems Corp.

High-Performance Small Form Factor Single-Chip Ethernet Controller with HP Auto-MDIX Support
Datasheet
Chapter 7 Operational Characteristics
SMSC LAN9211
7.1
7.2
Supply Voltage (VDD_A33, VDD_IO)
Positive voltage on signal pins, with respect to ground
Negative voltage on signal pins, with respect to ground
Positive voltage on XTAL1/CLKIN, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XTAL2, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (T
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 7.1
Note 7.2
Note 7.3
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 7.2, "Operating
applicable section of this specification is not implied.
Supply Voltage (VDD_A33, VDD_IO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V +/- 10%
Ambient Operating Temperature in Still Air (T
**Proper operation of the LAN9211 is guaranteed only within the ranges specified in this section.
Absolute Maximum Ratings*
Operating Conditions**
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
This rating does not apply to the following pins: XTAL1/CLKIN, XTAL2, EXRES1.
This rating does not apply to the following pins: EXRES1.
Conditions**",
DATASHEET
(Note
Section 7.6, "DC Electrical
137
7.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0V to +3.3V+10%
A
A
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
(Note
(Note
7.2) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
7.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
Specifications", or any other
Revision 2.3 (08-06-08)
o
C to +150
o
o
C to +70
C to +70
o
o
o
C
C
C