cp3bt26y98nepx National Semiconductor Corporation, cp3bt26y98nepx Datasheet - Page 127
cp3bt26y98nepx
Manufacturer Part Number
cp3bt26y98nepx
Description
Reprogrammable Connectivity Processor With Bluetooth-r, Usb, And Can Interfaces
Manufacturer
National Semiconductor Corporation
Datasheet
1.CP3BT26Y98NEPX.pdf
(280 pages)
- Current page: 127 of 280
- Download datasheet (5Mb)
19.6.4
The transmission process can be started after software has
loaded the buffer registers (data, ID, DLC, PRI) and set the
buffer status from TX_NOT_ACTIVE to TX_ONCE,
TX_RTR, or TX_ONCE_RTR.
When the CPU writes TX_ONCE, the buffer will be
TX_BUSY as soon as the CAN module has scheduled this
buffer for the next transmission. After the frame could be
successfully transmitted, the buffer status will be automati-
cally reset to TX_NOT_ACTIVE when a data frame was
transmitted or to RX_READY when a remote frame was
transmitted.
19.7
The CAN module has one dedicated ICU interrupt vector for
all interrupt conditions. In addition, the data frame receive
event is an input to the MIWU (see Section 13.0). The inter-
rupt process can be initiated from the following sources.
! CAN data transfer
— Reception of a valid data frame in the buffer. (Buffer
— Successful transmission of a data frame. (Buffer state
state changes from RX_READY to RX_FULL or
RX_OVERRUN.)
changes from TX_ONCE to TX_NOT_ACTIVE or
RX_READY.)
TX Buffer States
INTERRUPTS
RTR
received
transmit failed
TX_ONCE_RTR
TX_BUSY2
RX_READY
TX_RTR
1110
1111
1010
0010
CAN
schedules TX
TX done
Figure 61. Transmit Buffer States
Remote transmission
request sent - now wait
to receive a data frame
TX request delayed
by a TX request of higher
priority message
CPU writes 1010
127
Transmit
request cancelled
CPU writes 1000
TX_ONCE
If
TX_ONCE_RTR, it will transmit its data contents. During the
transmission, the buffer state is 1111b as the CPU wrote
1110b into the status section of the CNSTAT register. After
the successful transmission, the buffer enters the TX_RTR
state and waits for a remote frame. When it receives a re-
mote frame, it will go back into the TX_ONCE_RTR state,
transmit its data bytes, and return to TX_RTR. If the CPU
writes 1010b into the buffer status section, it will only enter
the TX_RTR state, but it will not send its data bytes before
it waits for a remote frame. Figure 61 illustrates the possible
transmit buffer states.
! CAN error conditions
The receive/transmit interrupt access to every message
buffer can be individually enabled/disabled in the CIEN reg-
ister. The pending flags of the message buffer are located in
the CIPND register (read only) and can be cleared by reset-
ting the flags in the CICLR registers.
1100
TX request
CPU writes 1100
— Successful response to a remote frame. (Buffer state
— Transmit scheduling. (Buffer state changes from
— Detection of an CAN error. (The CEIPND bit in the
TX request
CPU writes 1110
the
changes from TX_ONCE_RTR to TX_RTR.)
TX_RTR to TX_ONCE_RTR.)
CIPND register will be set as well as the correspond-
ing bits in the error diagnostic register CEDIAG.)
CPU
CAN
schedules TX
configures
TX_NOT_ACTIVE
transmit failed
TX_BUSY0
1000
1101
TX done
Transmit
request cancelled
CPU writes 1000
DS042
the
message
www.national.com
buffer
to
Related parts for cp3bt26y98nepx
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: